background image

The installation instructions are the basis for Security Agency Approvals.
The lock installation must be done in accordance to these instructions
in order to maintain the labeled approval level.

Design Parameters for Auditcon 2 Series Locks

1.  Bolt dimensions (nominal): .312 inches x 1.000 inches/8 x 25.4mm

2.  Bolt movement (nominal) : .465 inches/11.8mm

3.  Bolt extension:  .465 inches/11.8 mm
4.  Maximum load movable by the bolt:  5 lbs. (22N)

Note:

   

Auditcon 2 dead bolt locks may not open if more than 5 lbs.

(22N) of force is applied to the end or side of the bolt.

5. Maximum load against bolt when thrown (all directions): 224.8 lbs. (1kN)

6. The lock can be fitted to safes or vault doors of any material.

Note:

  

As is the case with all mechanical and electronic locking devices,

the container and boltworks must be designed to protect the lock.

Installation Instructions for Auditcon

®

 2 Series Locks - Models 52R, 252R, 552R - Round Housing Dead Bolt

Document # 3047.025  Rev. B - 12/06

Figure 1 - Dead Bolt Lock Parts

Dial Assembly

Cable

Cable
Shields (2)

Lock Case
Assembly

Lock Case
Mounting
Screws (4)

Dial
Assembly
Mounting
Screws (2)

Spindle &
Tube

Spindle
Mounting
Screw

Keypad
Assembly
with Decal

Part I:  Install Lock Case Assembly

WARNING:

Do not take the lock case assembly apart. There are

no field servicable parts inside lock case.

1. Insert a cable shield into the deburred spindle hole from the back
side of the container door.

2. Place the protective tube over the
tube retainer on the lock case. (Figure 2)

3. While holding the lock case assembly,
guide the tube through the spindle hole
and place the lock case flush against the
inside of the container door.

4. Mark the tube flush to the outside of
the container door (to within 1/16” or
1.6mm).

5. Remove lock case assembly from door
and cut the tube just inside your mark.

6. Plug one end of the ribbon cable into
the connector on the bottom of the lock
case. (Figure 3)

7. Lay the ribbon cable in the cable
routing path on the lock case and tape
the cable to the outside of the tube with
the insulator tape provided. (Figure 3)

8. Hold the lock case assembly and carefully guide the loose end of
the ribbon cable and the tube through the spindle hole so that they are
accessible outside of the container door.

9. Mount the lock case assembly to the inside of the container door
using the four 1/4-20 (or M6-1) lock case mounting screws. (Torque 25-
30 lbs., 2.8-3.4 N-M)

Note:

 

It is recommended that you use Loctite

®

 262 (Red) on the lock

case mounting screws.

10. Insert the end of the spindle with the screw hole into the lock case
assembly until the spindle is properly seated. The grooved side of the
spindle should be oriented so that the grooves in the spindle align with
the grooves in the drive cam. Turn the spindle to extend the bolt and
ensure that the grooves are facing toward the bolt.

11. Mark the spindle shaft 3/8” (9.5mm)
from the outside of the container door
(plus or minus 1/16” or 1.6mm allowed).
(Figure 4)

12. Remove the spindle from the lock
case to prevent damage to the cable
while cutting.

13. Cut the spindle on the mark and
deburr.

14. Re-insert the spindle. Refer to Step 10 for proper positioning.

Figure 4

Basic Tools and Materials Needed

Medium Phillips head screwdriver (#2)
(recommend magnetized tip)

9/64” Allen Wrench

Fine pitch hacksaw (32 teeth/inch)

Small flat file

All-purpose scissors

Tape measure or ruler

ESD wrist band

Recommended, but not required:

Torque screwdriver (30 inch-pounds/3.4
newton-meters capacity)

Small vise grip

Loctite

®

 262 (Red) for use on lock case

mounting screws

WARNING: Kaba Mas locks are protected
from 25,000 V Electrostatic Discharge
(ESD) damage when correctly installed.
Follow these precautions to avoid ESD
damage when installing the lock:
•  Handle the keypad assembly by the
outer edge only.
•  Use an ESD wrist band grounded to the
lock or container during installation.

Prepare for New Installation of the Lock 

(If Required)

1. Use the template provided to establish the exact locations
(relative to the spindle hole) of the mounting holes for the lock
assembly.

2. The spindle hole diameter can be a minimum of .406” (10.3mm) to
a maximum of .438” (11.1mm). The .406” (10.3mm) diameter is
recommended. Spindle hole must be deburred.

3. The dial assembly mounting screws require drilled and tapped
holes to 3/8” (9.5mm) depth if possible (minimum 1/4” or 6.4mm
depth required.) Drill either the two horizontal mounting holes or the
two vertical holes.

4. When mounting the lock unit (i.e., integrating it in a boltwork),
make sure that the lock bolt has clearance to freely move to its end
positions and that the shifting force works only in the axial direction
(direction of movement). Lateral forces should not be exerted on the
lock.

5. If other parts of the boltwork are to be connected to the lock unit
(e.g., for activating a blocking device), corresponding adapters can
be fixed with screws (#10-32 or M4) to the front of the lock bolt
(tightening torque for 15mm screwing depth: 200Ncm maximum).

Figure 2

Figure 3

Not Shown in Photo:  Insulator Tape

Содержание Auditcon 52R

Страница 1: ...te It is recommended that you use Loctite 262 Red on the lock case mounting screws 10 Insert the end of the spindle with the screw hole into the lock case assembly until the spindle is properly seated The grooved side of the spindle should be oriented so that the grooves in the spindle align with the grooves in the drive cam Turn the spindle to extend the bolt and ensure that the grooves are facin...

Страница 2: ...o place Figure 13 11 Test the operation of the lock before completing the installation of the keypad assembly by verifying the following Note If the keypad is not oriented correctly you can remove the keypad and adjust the orientation of the dial assembly Power the lock by turning the dial back and forth until simultaneous green and red flashes display and two beeps sound to indicate that the lock...

Страница 3: ...igure 3 Roller Slide Bolt Clearances StrikeTypes Contact Points Basic Tools and Materials Needed Medium Phillips head screwdriver 2 recommend magnetized tip 9 64 Allen Wrench ESD wrist band Recommended but not required Torque screwdriver 30 inch pounds 3 4 newton meters capacity Loctite 262 Red for use on lock case mounting screws WARNING Kaba Mas locks are protected from 25 000 V Electrostatic Di...

Страница 4: ...lowed by 502550 If the combination is entered successfully continuous green flashes display to indicate that the lock is ready to open Rotate the container handle to unlock Then rotate the handle back to the locked position Note After correctly entering a valid combination you must retract the bolt within 4 6 seconds 12 Unplug the RJ11 end of the cable from the lock case and lay the case aside 13 ...

Отзывы: