© Copyright
Gallo Technologies
. All Right Reserved
- 12 -
061515V54RS
22 Pin (Black) Wire Harness (Main Harness)
See Figure 1 for pin number and location.
Pin 1. (RED) Parking Light Pwr. w/15A fuse
Used to power the parking lights. Connect this wire to Bat + 12v.
Pin 2. (Yellow) Parking Lights Out (+).
Connect to the vehicles parking light circuit. If parking lights require more
than 10 amps (not normal) use an external 30 Amp relay.
Pin 3. (Blue/Red) NC-2
Used for central door locks. See Figure 2, 3, 4, 5, 6 for your vehicle’s door lock system.
Pin 4. (Blue/White) Com-2
Used for central door locks. See Figure 2, 3, 4, 5, 6 for your vehicle’s door lock system.
Pin 5. (Blue/Yellow) NO-2
Used for central door locks. See Figure 2, 3, 4, 5, 6 for your vehicle’s door lock system.
Pin 6. (Green/Red) NC-1
Used for central door locks. See Figure 2, 3, 4, 5, 6 for your vehicle’s door lock system.
Pin 7. (Green/White) Com-1
Used for central door locks. See Figure 2, 3, 4, 5, 6 for your vehicle’s door lock
system.
Pin 8. (Green/Yellow) NO-1
Used for central door locks. See Figure 2, 3, 4, 5, 6 for your vehicle’s door lock system.
Pin 9. (Purple) Trunk output (-).
Trunk Release Output Neg. (-). Connect to the trunk release Neg. (-) trigger wire
on the vehicle’s trunk release relay. In the event that a trunk release is to be added to the vehicle, an additional relay
and trunk release solenoid will be required.
Pin 10. (White/Black) Arm Output (-)
Is a neg. (-) output when the alarm is triggered. Can be used to activate other
alarm triggered devices. (125 ma max.)
Pin 11. (White/Blue) Auxiliary output (-)
This is a low current (-) output (125ma max). It can be used to activate the
(-) neg side of a relay that may be used for operating the passenger door of a shaved door vehicle, an extra trunk
release or an electric window close operation. Connect to a window close module (not included) with a Neg. (-)
input. Follow the window close module instructions for wiring to window motors. Do not connect this wire directly to
the vehicle’s window close switch. The output duration can be either 2 sec or 15 sec per Table #1 option 8, page 9.
Pin 12. (RED) Module Power. w/5A fuse
Used to power the GTS-3RS Control Module. Connect this wire to Bat +
12v.
Pin 13. (White) Ignition 2 output (-)
Used to activate an additional relay so that an IGN 2 circuit may be used when
the vehicle requires its use. Not all vehicles require an IGN 2 circuit. Pin4 must be connected to the (-) neg terminal
of the relay. See Figure 1, option 2.
Pin 14. (Purple/White) Start Enable input (-) input.
Connect to a good chassis ground (-).
Pin 15. (Black) Ground (-)
Connect to a good chassis ground (-).
Pin 16. (Orange/White) Handbrake (-).
Connect to the handbrake switch that is neg (-) when handbrake is set.
Pin 17. (White/Red) Disarm Output (-) Ground While Running (GWR)
. Connect to the Neg (-) input of a security
bypass device. These devices are used in the event that the vehicle has an OEM security system that prevents
starting the vehicle without the security key. The proper security by-pass module for the specific vehicle can be
found at
www.gallotech.com/support
. Follow the instruction that came with the by-pass module.
This wire is activated only during engine starting and running. When the engine is turned OFF there will be no GWR
output.
Pin 18. (Black/White) Foot Brake input (+)
(+12v) Foot Brake Switch Input Used for auto door lock function and
Starting. Connect to Foot brake switch terminal that has +12v only when foot brake is depressed.
Pin 19. (Brown/Black) Door (+) input. Pos. (+) Door Switch Input.
Connect to a Pos. (+) Door Trigger switch. If
the vehicle has “-” Neg. Door Trigger use the (Brown/White, Pin 18) wire instead. Tape or wire nut wire if not used.
Pin 20. (Brown/White) Door (-) input. Neg. (-) Door Trigger switch Input.
Connect to the Neg. (-) Door Trigger
switch. If the vehicle has “+” Pos Door Trigger, use the (Brown/Black), Pin 16) wire instead. Tape or wire nut wire if
not used.
Pin 21. (Light Blue) Tach Input. Before connecting see Sec 1.4 “
Voltage/ Tach signal detection Options”
.
Pin 22. (Brown) Siren/Horn output (+).
+12v Output. Connect to the RED Siren wire. Connect the second siren
(Black) wire to a good chassis ground. If the vehicle’s horn is used; connect Pin 22 (Brown) wire to the (+) pos
terminal on the horn relay. Do not connect directly to the horn. Table #1 option 10 must be changed to either Siren
or Horn.
Installing Connector C3:
