Gallo Tech GStarter I Скачать руководство пользователя страница 6

Страница: 6 / 12

© Copyright

Gallo Technologies

- 6 -

52008

Table 1: FUNCTION OPTION CHART

Parking lights flash 3 times or 1 time to indicate the function state

“Engine

Start”

button

OFF/ON

n th times

Function To Set

Parking lights

Flash 3 times

Parking Lights

Flash 1 time

1 time

Valet Mode

Disable

Enable (factory default)

2 times

Key FOB

Code learning

Follow steps 1& 2 above to enter programming mode. Press ENGINE

START button OFF/ON 2 times and hold at ON position, After 2 seconds

parking lights will flash 2 times to indicate code learning is activated.

Then press any button of the transmitter. The parking lights will flash 4

times to indicate the key FOB code has been successfully learned. Each

FOB must be programmed.

3 times

Passive arming

Enable

Disable (factory default)

4 times

Passive locking

Enable

Disable (factory default)

5 times

Locking Time

4 sec.

0.4sec (factory default)

6 times

Ignition Key Door

locking/unlocking

Enable

Disable (factory default)

7 times

Active Arm & Lock

Enable

Disable (factory default)

8 times

Lock/unlock Siren

Chirp

Disable

Enable (factory default)

9 times

Two Pulse

locking/unlocking

Enable

Disable (factory default)

10 times

Ignition Key Start

Function

Disable

Enable (factory default)

11 times

Disable Start

Button Cut Off Delay

Parking lights flashes 1 time to indicate enabled (factory default)

12 times

30 Second

Start Button Cut Off

Delay

Parking lights flashes 1 time to indicate enabled

13 times

60 Second

Start Button Cut Off

Delay

Parking lights flashes 1 time to indicate enabled

14 times

5 minutes

Start Button Cut Off

Delay

Parking lights flashes 1 time to indicate enabled

15 times

10 minutes Start

Button Cut Off Delay

Parking lights flashes 1 time to indicate enabled

* When installing as a stand alone “Engine Start” configuration (without door lock & alarm functions) the only

functions that can be used are those marked with an (*).

Содержание GStarter I













Результаты поиска

Содержание GStarter I

Отзывы:

Похожие инструкции для GStarter I

Бренды по названию

Популярные бренды

Gallo Tech GStarter I, Руководство по эксплуатации и установке

Результаты поиска

Содержание GStarter I

Отзывы:

Похожие инструкции для GStarter I

Бренды по названию

Популярные бренды