manualshive.com logo in svg

Galil Motion Control DMC-14 5 Series, Руководство пользователя

Поделиться
Скачать
Galil Motion Control DMC-14 5 Series Скачать руководство пользователя страница 66

The Begin (BG) command can be issued for all axes either simultaneously or independently.  X or Y 
axis specifiers are required to select the axes for motion.  When no axes are specified, this causes 
motion to begin on all axes.   

The speed (SP) and the acceleration (AC) can be changed at any time during motion, however, the 
deceleration (DC) and position (PR or PA) cannot be changed until motion is complete.  Remember, 
motion is complete (AM) when the profiler is finished, not when the actual motor is in position.  The 
Stop command (ST) can be issued at any time to decelerate the motor to a stop before it reaches its 
final position. 

An incremental position movement (IP) may be specified during motion as long as the additional move 
is in the same direction.  Here, the user specifies the desired position increment, n.  The new target is 
equal to the old target plus the increment, n.  Upon receiving the IP command, a revised profile will be 
generated for motion towards the new end position.  The IP command does not require a begin.  Note:  
If the motor is not moving, the IP command is equivalent to the PR and BG command combination. 

Command Summary - Independent Axis 

 Command 

 Description 

PR x,y 

Specifies relative distance 

PA x,y 

Specifies absolute position 

SP x,y 

Specifies slew speed 

AC x,y 

Specifies acceleration rate 

DC x,y 

Specifies deceleration rate 

BG XY 

Starts motion 

ST XY 

Stops motion before end of move 

IP x,y 

Changes position target 

IT x,y 

Time constant for independent motion smoothing 

AM XY 

Trippoint for profiler complete 

MC XY 

Trippoint for "in position" 

 

The lower case specifiers (x,y) represent position values for each axis.  

The DMC-14XX also allows use of single axis specifiers such as PRY=2000   

Operand Summary - Independent Axis 

 

Operand Description 

_ACx 

Return acceleration rate for the axis specified by ‘x’ 

_DCx 

Return deceleration rate for the axis specified by ‘x’ 

_SPx 

Returns the speed for the axis specified by ‘x’ 

_PAx 

Returns the last command position at which motion stopped 

_PRx 

Returns current incremental distance specified for the ‘x’ axis 

Example - Absolute Position Movement 

PA 10000,20000 

Specify absolute X,Y position 

AC 1000000,1000000 

Acceleration for X,Y 

DC 1000000,1000000 

Deceleration for X,Y 

SP 50000,30000 

Speeds for X,Y 

BG XY 

Begin motion 

DMC-14x5/6 

Chapter 6  Programming Motion 

i

 57 

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание DMC-14 5 Series









































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды