Galaxy GHDX2-2430S-16F4D Скачать руководство пользователя страница 57

Страница: 57 / 100

Galaxy GHDX2-2430S-16F4D Installation and Hardware Reference Manual

4-6

Power

Figure 4-2: Connect GHDX2-2430S-16F4DSubsystem to Single Host

•

Connections:

The input ports on the subsystem, FC-CH0 and FC-

CH1, are connected to two separate HBAs on a host computer.

4.4 Power On

Once all of the components have been installed in the GHDX2-2430S-

16F4D and the host channels have been connected to the host, the

subsystem can be powered on.

4.4.1 Check

List

BEFORE

powering on the GHDX2-2430S-16F4D, please check the

following:

Memory module:

Memory modules have been correctly installed

on the controller boards.

BBU:

If BBU is installed, make sure BBU has been installed

correctly.

Hard drives:

Hard drives have been correctly installed in the drive

trays.

Drive trays:

All the drive trays, whether or not they contain a hard

drive, have been installed into the subsystem.

Cable connections:

The host ports on the subsystem have been

correctly connected to a host computer(s).

Power cords:

The power cords have been connected to the PSU

modules on the subsystem and plugged into the main power source.

Ambient temperature:

All the subsystem components have been

acclimated to the surrounding temperature.

Содержание GHDX2-2430S-16F4D





































































































Результаты поиска

Содержание GHDX2-2430S-16F4D

Отзывы:

Похожие инструкции для GHDX2-2430S-16F4D

Бренды по названию

Популярные бренды

Galaxy GHDX2-2430S-16F4D, Руководство по установке и аппаратным средствам

Результаты поиска

Содержание GHDX2-2430S-16F4D

Отзывы:

Похожие инструкции для GHDX2-2430S-16F4D

Бренды по названию

Популярные бренды