Galaxy GHDX2-2430S-16F4D Скачать руководство пользователя страница 49

Страница: 49 / 100

Galaxy GHDX2-2430S-16F4D Installation and Hardware Reference Manual

3-10

Audible Alarm

3.3. Audible

Alarm

Different controller environmental and operational parameters (like

temperature, etc.) have been assigned a range of values between which they

can fluctuate. If either the upper or lower thresholds are exceeded, an

audible alarm will automatically be triggered. The alarm will also be

triggered when an active component on the GHDX2-2430S-16F4D fails. If

the user / manager is onsite and hears an alarm, the manager must read the

error message on the LCD screen or PC terminal to determine what has

triggered the alarm. After determining what has occurred, the manager must

take appropriate actions to rectify the problem.

WARNING!

If an alarm is triggered, it is necessary for you to determine the problem.

If the audible alarm is ignored and the problem is not rectified,

unexpected damages may occur.

3.3.1 Default Threshold Values

NOTE:

The threshold values listed below are used to trigger a warning event and

sound the alarm. A different value set is reserved for triggering the

cooling fans to operate at a high rotation speed. The fan speed value set

is not user-configurable.

Table 3-9

shows the default threshold values for the GHDX2-2430S-16F4D.

If any of these values are surpassed, the alarm will sound:

Parameter

Upper

Threshold

Lower

Threshold

+3.3V

+3.6V +2.9V

+5V

+5.5V +4.5V

+12V

+13.2V +10.8V

CPU Temperature

90ºC 5ºC

Board Temperature

80ºC 5ºC

Enclosure Ambient

Temperature

40ºC 0ºC

Table 3-9: Default Threshold Values

The thresholds in

Table 3-9

are the default threshold values. To change

these pre-set values, please refer to the

User’s Operation Manual

that came

with your system. The values set for the subsystem’s ambient temperature

are pre-configured before shipping and cannot be changed.

Содержание GHDX2-2430S-16F4D





































































































Результаты поиска

Содержание GHDX2-2430S-16F4D

Отзывы:

Похожие инструкции для GHDX2-2430S-16F4D

Бренды по названию

Популярные бренды

Galaxy GHDX2-2430S-16F4D, Руководство по установке и аппаратным средствам

Результаты поиска

Содержание GHDX2-2430S-16F4D

Отзывы:

Похожие инструкции для GHDX2-2430S-16F4D

Бренды по названию

Популярные бренды