Galaxy GHDX2-2430S-16F4D Скачать руководство пользователя страница 28

Страница: 28 / 100

Chapter 2: Hardware Installation

Installation Overview

2-1

Chapter 2

Hardware Installation

2.1. Installation

Overview

This chapter gives detailed instructions on how to install the controller

module, hard drives, and drive trays into the subsystem. Installation into a

rack or cabinet should occur before the hard drives or drive trays are

installed into the subsystem. Please confirm that you received all of the

components listed on the

Unpacking List

that came with the subsystem

before proceeding with the installation process.

CAUTION!

Please note that the installation instructions described in this manual

should be carefully followed to prevent any difficulties and damages to

your system.

2.2. Installation

Pre-requisites

Static-free installation environment:

The GHDX2-2430S-16F4D

Galaxy Raid subsystem must be installed in a static-free environment to

minimize the possibility of electrostatic discharge (ESD) damage. (See

Section 2.3

)

Component check:

Before installing the GHDX2-2430S-16F4D

subsystem, you should first check to see that you have received all the

required components. (See

Section 2.5

) If any items appear damaged,

contact your vendor for a replacement.

Hard drives:

Up to sixteen (16) SATA-II or SATA-I hard drives have

been preinstalled into drive trays and are ready to be installed in the

Galaxy Raid subsystem. (See

Section 2.6

)

Cabling:

All Fibre cables used to connect the subsystem to the host

computers or external devices must be purchased separately. Please see

Содержание GHDX2-2430S-16F4D





































































































Результаты поиска

Содержание GHDX2-2430S-16F4D

Отзывы:

Похожие инструкции для GHDX2-2430S-16F4D

Бренды по названию

Популярные бренды

Galaxy GHDX2-2430S-16F4D, Руководство по установке и аппаратным средствам

Результаты поиска

Содержание GHDX2-2430S-16F4D

Отзывы:

Похожие инструкции для GHDX2-2430S-16F4D

Бренды по названию

Популярные бренды