background image

D.  Try a different location on your car (keeping in mind the radiation pattern 

you wish) 

 

E.  Is the antenna perfectly vertical? 

 

F.  Try a different location in your neighborhood. Stay away from large 

metal objects when adjusting (metal telephone or light posts, fences, etc.). 

 

 

 
 
 
 

 

EXTERNAL SPEAKER 

The external speaker jack (EXT.SPK) on the rear panel is used for remote 

receiver monitoring. The external speaker should have 8 ohms impedance and be 
able to handle at least 4 watts. When the external speaker is plugged in, the internal 
speaker is disconnected. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Operation 

 

CONTROL FUNCTIONS 

There are thirteen controls and three indicators on the front panel of your 

transceiver. 

 

 

FRONT PANEL 

 

1.  OFF/ON/VOLUME (inner dual concentric). 

Turn clockwise to apply power 

to the unit and to set the desired listening level. During normal operation, the 
VOLUME control is used to adjust the output level obtained either at the 
transceiver speaker or the external speaker, if used. 

 
2.  SQUELCH (outer dual concentric). 

This control is used to cut off or 

eliminate receiver background noise in the absence of an incoming signal. For 
maximum receiver sensitivity it is desired that the control be adjusted only to 
the point where the receiver background noise or ambient backgrounds noise is 
eliminated. Turn fully counterclockwise then slowly clockwise until the 
receiver noise disappears. Any signal to be received must now be slightly 
stronger than the average received noise. Further clockwise rotation will 
increase the threshold level, which a signal must overcome in order to be 
heard. Only strong signals will be heard at a maximum clockwise setting.   

 

3.  MIC GAIN (inner dual concentric).

 Adjust the microphone gain in the 

transmit and PA modes. This controls the gain to the extent that full talk power 
is available several inches away from the microphone. 

 

4.  RF GAIN CONTROL (outer dual concentric). 

Use to reduce the gain of the 

RF amplifier under strong signal conditions. 

 

The transceiver will operate into an SWR of 2 to 1 indefinitely 
and sustain an SWR of 20:1 for a maximum of 5 minutes at rated 
operating conditions. 

- 8 - 

- 7 - 

NOTE 

Содержание DX 44V









Отзывы: