background image

5.  MODE (PA/FM/AM) SWITCH. 

This switch is used to select PA, FM, AM 

mode of operation. The AM or FM mode is normally, but when you set to PA 
position, the transceiver acts as a public address amplifier. Before operating 
PA, you must first connect an external PA speaker (8 ohm, more than 2W) to 
the PA Speaker jack on the unit rear panel.

 

 
6. BAND 

SELECTOR. 

This switch selects A, B, C, D, E, F, G or H band of 

operation.

 

 
7. E-TONE.

 This control is used to echo effect and intervals of echo sound.

 

 
8.  RF POWER CONTROL.

 Adjust this control to acquire RF power level you 

desired in AM or FM transmission.

 

 
9. CHANNEL 

SELECTOR.

 This switch selects any one of the forty channels 

desired. The selected channel appears on the LED readout directly above the 
Channel Selector knob.

 

 
10. METER.

 This meter indicates received signal strength, transmitter RF output 

power.

 

 
11. BEEP/DIMMER SWITCH.

 This switch is used to select ROGER BEEP and 

lower the level of brightness of display.

 

 
12. BAND SWITCH-HI/LOW.

 This switch is used to select High band and or 

Low band Frequency Range.

 

 
13. +10KHz FREQUENCY SHIFT SWITCH. 

When switch is pressed the 

frequency is shifted 10KHz up. On following channels. A channel can be used 
by setting this switch to +10KHz position. 

 

10KHz 

3 3A 
7 7A 

11 11A 
15 15A 
19 19A 

 
14. OFF/ANL/NB. 

When the switch is placed in the ANL + NB position, the RF 

noise blanker also is activated. The RF noise blanker is very effective for 
repetitive impulse noise such as ignition interference.

 

 
 
15. RECEIVER/TRANSMIT  INDICATOR. 

The receiver/transmit LED 

indicator is located next to the channel indicator. When in receive, the LED 
will be green. When in transmit the LED will be red.

  

 
16. CHANNEL INDICATOR.

 Numbered LED indicates the selected channel 

you wish to operate on. LED indicates “9” when CH-9 is switched on.

 

 
REAR PANEL 

 

 

 
17. POWER. 

Accepts 13.8V DC power cable with built-in fuse (4 amp.) to be 

connected. 

 
18. EXT SP. 

Accepts 4 to 8 ohms, 5 watt external speaker to be connected. When 

external speaker is connected to this jack, the built-in speaker is automatically 
disconnected. 

 

19. PA. SP.

 Used to connect a PA speaker (8 ohm 4W) for PA operation. Before 

operating PA you must first connect a PA speaker to this jack. 

 

20. ANTENNA.

 Accepts 50 ohm coaxial cable with a type PL-259 plug to be 

connected. 

 

21. F.C. 

This socket is optional for the accessories FREQUENCY COUNTER 

model FC-347, to indicate the value of the frequency ranges used.

 

 
 
 
 
 
 
 
 
 

- 9 - 

- 10 - 

Содержание DX 44V









Отзывы: