background image

P

AGE 

11 of 14

M

ODEL 

TI984 T

ELEPHONE 

I

NTERFACE

42004-071F

f:\standard ioms - current release\42004 instr. manuals\42004-071f.doc

05/03

Programming Table

Function

RESET UNIT TO FACTORY CODES (DEFAULT)

KEY SEQUENCE

# #

DESCRIPTION

(Day Mode)

Voice access method (for incoming calls)
7-second voice page
60 seconds after the page for the call to be answered before disconnection
Auto-connect enabled
4 incoming rings before TI984 enters page mode
7 second hang up delay
Internal Day/Night switch

DESCRIPTION

(Night Mode)

Ring access method (for incoming calls)
1 incoming ring before TI984 generates a ring tone on the page line
7 second hang up delay
Internal Day/Night switch

*Function

SELECT INCOMING CALL - MANUAL ACCESS METHOD

KEY SEQUENCE

# 3 3

DESCRIPTION

If selected, a switchboard operator must manually connect the telephone call to the
Page/Party

®

 system by pressing the 

A

CCESS

 button on the front cover of the TI984.

The incoming call is automatically transferred to the designated party line, provided
a station is off-hook on the designated party line.

*Function

SELECT INCOMING CALL - VOICE ACCESS METHOD

KEY SEQUENCE

# 3 0 P P

 

M M

 

A

DESCRIPTION

If selected, incoming calls are transferred directly to page line.

PP 

= number of seconds of voice page (00 to 99)

MM

 = number of seconds after a page that the call must be answered (00 to 99) or

the call is disconnected (auto-connect DISABLED).
With auto-connected ENABLED, the call is transferred directly to the
designated party line after the page, provided the designated party line is in use.

A

 = auto-connect option:  

1

 to enable or 

0

 to disable

Example: To set a 15-second voice page, a 25-second period after the end of the
page before the call reverts to the auto-connect option, and to enable the auto-
connect option, enter the following code:  

# 3 0 1 5 2 5 1

*Function

SELECT INCOMING CALL - RING ACCESS METHOD

KEY SEQUENCE

# 3 1

DESCRIPTION

If selected, incoming calls are transferred directly to the page line after a
programmed number of rings have elapsed.  To answer the call, someone must take
a Page/Party

®

 station off-hook on the designated party line.

Содержание TI984

















Отзывы: