G-Scale Graphics RailBoss Plus Скачать руководство пользователя страница 25

 

Page 25 

Recommended Radio Systems 

We  do  not  sell  radio  transmitters,  but  we  do  sell  DSM2  compatible  receivers. 

There are many low cost 2.4 

GHZ hobby radios available, with more coming all the time. Only 4-Channels are required, with one being a digital 
proportional throttle. Either Mode 1 (throttle on the right) or Mode 2 (throttle on the left). Simultaneous operation of 
two trains requires a 5th channel controlled via a toggle switch on the transmitter.  
 
2.4GHz is approved for both surface and air use. 
 
In most cases, installing the receiver in a metal body will still work. But  you may want to select one with an ex-
tended antenna. The last inch is the actual antenna, which may need to protrude outside of the metal body. 
 

Spektrum 

Any of the products in the Spektrum DX line will work, however, the DX5E is the most economical. This line is as-
sumed to be of the highest quality and most reliable. 
 
DX5E Transmitter  

 

 

 

 

$59 

www.HorizonHobbies.com or Local Hobby Shop 

G-Scale Graphics DSM2 compatible Receiver 

 

$15 

 
Many DSM2 compatible receivers are available that will work with Spektrum transmitters   

$8 to $19 

 

TargetHobby.com 

AR6100, AR6100E 

 

HobbyKing.com  

Orange Rx 

 

 

And others  
 
Note: Spektrum receivers with the “SmartSafe” failsafe feature are not fully compatible with the RailBoss, includ-
ing the 

genuine 

Spektrum AR6100 and AR600 purchased from your local hobby shop. 

 

These will also work ... 

Spektrum 

DX6i 

 

Used by many for radio control of live steam locomotives

 

 
Hobby King 2.4GHZ 

Hobby King T6A 6-Channel Transmitter and Receiver 

<$32 

www.HobbyCity.com 

Hobby King 6-Channel Receiver  

 

 

<$10 

 

 
 
 
 
 
 
 

 

 

Содержание RailBoss Plus



























Отзывы: