9
Disconnect the chainsaw from the power source if the
power cable is damaged or cut.
The chain saw may only be connected to socket
outlets with a ground contact and tested electrical
installations. We recommend the use of a residual-
current-operated circuit-breaker.
The cable must be fully unwound when you use a
cable reel.
Ensure that the power cable has no kinks and is not
damaged.
Always position the cable so, that it will not be caught
on branches and the like, during cutting.
The chain saw may only be used in a completely
assembled state. No protective devices may be
missing.
Switch the chain saw off immediately if you notice any
changes in the machine.
Always have a first-aid kit at hand in case of
accidents.
If the chain saw comes into contact with earth,
stones, nails or other foreign objects, withdraw the
plug immediately and check the chain as well as the
bar.
Ensure that no chain oil penetrates into the earth or
sewage. Always place the chain saw on something
that will absorb any oil dripping from the bar or chain.
Avoid using the chainsaw in poor weather conditions,
especially if there is a risk of a thunderstorm.
WARNING TO THE DANGER OF RECOIL
If possible, use a stand.
Always keep an eye on the bar tip.
Only place a running saw on the object to be cut.
Never start the machine while the chain rests on
something.
So called piercing cuts with the bar tip may only be
carried out by trained personnel.
SAFE WORKING TECHNIQUES
Working on ladders, scaffoldings or trees is forbidden.
Ensure that the wood cannot twist while it is being
cut.
Watch out for splintering wood. While you are sawing
you may be injured by flying wood chips.
Do not use the chain saw to lever or move the wood.
Only cut with the lower section of the saw. The saw
will be repulsed towards you if you try and cut with
the upper section of the saw.
Ensure that the wood is free of stones, nails or other
foreign objects.
We recommend that first-time users are instructed
practically as to the correct use of the chainsaw and
the required personal safety equipment by an
experienced operator; the cutting of round wood or
logs should be trained on a log stand or similar rack-
type device first.
Keep the running chainsaw from touching the ground
or wire fences.
Warning! The operation of any power tool can result in
foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning
power tool operation, always wear safety goggles or
safety glasses with side shields and, when needed, a
full face shield. We recommend Wide Vision Safety
Mask for use over eyeglasses or standard safety
glasses with side shields. Always use eye protection
which is marked to comply with ANSI Z87.1.
BEFORE CONNECTING TO THE MAINS SUPPLY
Examine the mains cable for any damage caused by
chafing or cuts from sharp objects. If the cable is
damaged replace the complete cable.
Examine the chain for signs of damage, sharpness,
missing teeth and for the correct tension. Examine the
guide bar, nose guard for any damage or excessive
wear.
Check the tightness of the guide bar securing nuts
and tighten if necessary.
Check the sharpness of the spiked bumper and
sharpen if required.
Check the level of the chain oil in the reservoir and
replenish if required with a good quality chain oil.
Check the residual current device (RCD) for correct
operation.
GENERAL SAFETY RULES
WARNING!
Read all instructions Failure to follow all
instructions listed below may result in electric shock,
fire and/or serious injury. The term "power tool" in all
of the warnings listed below refers to your mains
operated (corded) power tool or battery operated
(cordless) power tool.
SAVE THESE INSTRUCTIONS
1) WORK AREA
a) Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
All manuals and user guides at all-guides.com
Содержание FXAYT4394-03
