FXA FXAYT4394-03, Инструкция по эксплуатации

Страница: 12 / 112

12
Before filling the oil tank, ensure that the chainsaw is
disconnected from the mains supply.
Remove the oil filler cap (Fig.6) (6.1) and place safely
aside so that the sealing ring in the tank cap does not
get lost. Fill approx 120ml of oil into the tank using a
funnel and screw on the oil filler cap tightly once
more.
It is possible to check the oil level at the oil level
indicator (Fig.6) (6.2). The oil level must never fall
below the minimum level indicator.
Do not allow sawdust or wood debris into the oil
reservoir, this will clog the lubrication system.
If you do not intend to use the machine for an
extended period, please empty the oil tank of chain
oil.
The oil tank should also be emptied before the
chainsaw is transported or sent for repair.
CHECKING THE LUBRICATION SYSTEM
To check that the lubrication system is working, run
the chainsaw while holding the guide bar above some
paper. A steadily increasing stain caused by oil spray
shows that the lubrication system is working. If there
is no oil stain check and clean the lubrication system
before using the chainsaw. The chainsaw must never
be run without the oilier in full working condition.
OPERATION
CONNECTING TO A POWER SUPPLY
The voltage and current supply must comply with the
ratings on the rating label. Before commencing work,
always check that the chainsaw works properly and is
safe to operate. Check also that the chain lubrication
and the oil gauge are in good working order.
This product is designed with a power cable
retainer that prevents the extension cord from being
pulled loose while using.
Form a loop with the end of the extension cord.
Insert loop portion of extension cord through the
opening in the bottom of the rear handle and place
over power cable retainer, Fig.7.
Slowly pull loop against power cable retainer until the
slack is removed.
Plug product into extension cord.
NOTE: Failure to remove all excess cord slack from
extension cord retainer could result in plug loosening
from the receptacle.
NOTE: Use only approved outdoor extension cords.
NOTICE: Always use cord retainer to properly
attach extension cord to chainsaw. Failure to use cord
retainer may result in damage to chainsaw and/or
extension cord.
SWITCHING ON
Hold the saw securely with both hands so that the
thumbs and fingers are wrapped around the handle of
the chain saw.
Press with your thumb the safety lock button, Fig.8 (A)
on the left side of the rear handle and then the on/off
trigger, Fig.8 (B).
The safety lock button is used for unlocking the
switch-on mechanism and does not need to be
pressed again after the device is switched on.
To switch off the device, release the on/off trigger.
Warning! The sawing chain will start running at high
speed immediately. When putting the saw down,
make sure that the chain never touches stones or
metal objects.
SAFETY DEVICES ON YOUR CHAIN BRAKE
CHAIN BRAKE
This chainsaw is equipped with a mechanical brake
for the chain. In the case of uncontrolled movements,
when the tip of the saw blade gets in contact with
wood or a solid object, the drive of the chain is
immediately stopped by activation of the hand guard,
Fig.9 (B), the motor will not be stopped. This brake
function is initiated by the back of your hand on the
front handle Fig.9 (A) pushing the Fig.9 (B) hand
guard. The proper function of the saw chain brake
shall be checked before each use of the saw.
About every 10 hours of operation, the chain brake
should be checked for its proper function. After the
chain brake has been activated, wait for the motor to
come to a halt before you engage the clutch again. Do
not unnecessarily activate the chain brake as this may
result in increased wear and tear.
Caution! No buttons should be pressed when the
chain brake is released (hand protection pulled back
in the direction of the handle and locked).
Always ensure before starting the chainsaw that the
hand protection Fig.9 (B) is locked in the operating
position. To do this, pull back the hand protection in
the direction of the handle.
RUNDOWN BRAKE
In accordance with the latest regulations, this
chainsaw is equipped with a mechanical rundown
brake. This brake is connected to the chain brake and
stops the running chain after the chainsaw has been
switched off.
It is activated by releasing the on/off trigger. The
rundown brake avoids injuries through the coasting of
the chain.
All manuals and user guides at all-guides.com