FXA FXABGAG-2000-ZSII, Инструкция по эксплуатации

Страница: 8 / 60

8
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is
maintained.
COMPONENTS & CONTROLS (FIG 1)
OPERATING INSTRUCTIONS
WARNING! THIS MACHINE IS INTENDED TO
FUNCTION AS A GRINDER ONLY
Use the tool only for approved applications.
Operations such as cutting, sanding, wire brushing,
polishing are not recommended to be performed with
this power tool.
ANGLE GRINDER CONTROLS (PICS. 2 & 3)
Looking at the Angle Grinder from the top the spindle
lock is located at the front centre of the gearbox
casing (Pic.2). The location points for the handle (to
suit left or right handed operators) are located each
side of the grey gearbox housing at the front of the
Angle Grinder. A direction arrow to show the direction
of disc rotation is located at the front of the grey
gearbox housing. The On/Off switch is located
underneath the rear hand grip. Turn the Angle Grinder
onto its back and locate the adjustable disc guard
(Pic.3). The drive spindle can be seen along with the
disc locking nut and the backing disc washer (Refer to
installing the cutting discs).
FITTING THE DISC GUARD (PIC. 4)
NOTE: The disc guard must be fitted to the Angle
Grinder at all times during use. Locate the disc guard
onto the guard mounting spigot and secure by
tightening the hex socket screw (Pic.4)
INSTALLING GRINDING DISCS (PICS. 3 & 5)
Make sure the Angle Grinder is unplugged from the
mains supply socket. Turn the Angle Grinder onto its
back (Pic.3).
Locate and depress the spindle lock button. Using the
wrench supplied insert the pins into the holes on the
disc clamping nut.
Turn the wrench anti-clockwise to release the disc
clamping nut.
If the disc backing washer is removed it must be
replaced the correct way round. The correct way to fit
this onto the shaft can be seen in Pic.5.
NOTE: There are different types of discs used for
different applications. Select the correct one for the
work being done.
Make sure the disc backing washer flats are located
correctly with the flats on the shaft. The grinding disc
should be placed onto the Angle Grinder with the
writing facing upwards.
INSTALLING A NEW DISC (PICS. 6 & 7)
Place the disc over the shaft locating it onto the disc
backing washer. It can be seen that the backing
washer has a raised lip.
The hole in the disc should match the diameter of the
raised lip, keeping the disc mounted central (Pic.6)
Refit the disc clamping nut (Pic.6). Tighten with fingers
until the disc is clamped.
Locate and depress the spindle lock and using the
supplied wrench, (Pic.7) tighten the locking washer in
a clockwise direction until the disc is firmly clamped
but do not over tighten. Release the spindle lock and
turn the Angle Grinder over.
The side handle can be fitted to either side of the
machine to suit the operator (Pic.8) ensure that the
side handle is secured but do not over tighten.
Connect the Angle Grinder to a suitable mains supply
socket. It is advisable to use an approved Residual
current device (RCD).
If in doubt consult an approved electrician.
FOR YOUR SAFETY PLEASE FOLLOW THE THESE
INSTRUCTIONS
Working with an Angle Grinder should always be done
in a suitable designated work area for safety reasons.
Hot sparks are generated when grinding or cutting.
Any debris nearby could be ignited resulting in a fire.
Read all the safety instructions before using the Angle
Grinder.
START/STOP AND ADJUSTMENT OF THE
POSITION OF THE REAR GRIP (PIC 9).
This tool is fitted with a safety device that prevents
accidental activation. To start the tool, use your index
finger to pull back the safety trigger (9.2) on the
ON/OFF button (9.1) and press the ON/OFF button at
the same time. While using the tool, you can relax the
pressure of your index finger on the safety trigger. To
stop, press the ON/OFF button.
The rear grip can be rotated 90° top the left or right.
Press the lock button (9.3) and turn the grip in the
direction required. Release the lock button making
sure that it has returned completely in its housing.
If the machine makes an unfamiliar sound or vibrates
excessively switch it off immediately and disconnect
from the power supply.
1. Angle grinder
2. Spindle lock
3. Backing washer
4. Disc clamping nut
5. Guard
6. LH & RH handle points
7. On/Off
8. Handle
9. Wrench