FXA FXABGAG-2000-ZSII, Инструкция по эксплуатации

Страница: 9 / 60

9
Investigate the cause or consult a service centre for
advice.
Wherever possible the work piece should always be
secured in a clamp or vice.
TO USE THE GRINDER
ATTENTION:
Do not switch the grinder on whilst the
disc is in contact with the workpiece. Allow the disc to
reach full speed before starting to grind.
Hold your angle grinder with one hand on the main
handle and other hand firmly around the auxiliary
handle.
Always position the guard so that as much of the
exposed disc as possible is pointing away from you.
Be prepared for a stream of sparks when the disc
touches the metal.
For best tool control material removal and minimum
overloading, maintain an angle between the disc and
work surface of approximately 5º-15º when grinding,
Pic.10.
Use caution when working into corners as contact with
the intersecting surface may cause the grinder to jump
or twist.
When grinding is complete allow the workpiece to cool.
Do not touch the hot surface.
During use it is advisable to periodically check the
security of the disc clamping nut, side handle and disc
guard.
Be aware that grinding metal can cause harmful dust
particles that will damage your respiratory system and
it is advised that an approved dust mask is obtained
from a reputable dealer.
NEVER immerse the grinding disc into any type of
lubricant including water. The Angle Grinder is a dry
grinder. Failure to observe will result in a fatal electric
shock.
The guard is adjustable for different types of work. The
picture 11 shows how the guard has been adjusted to
deflect the sparks away from the operators eyes. See
safety instructions for additional protective equipment.
Always keep mains power lead to the rear of the work
being grind.
MAINTENANCE
Remove the plug from the socket before carrying out
any adjustment, servicing or maintenance.
There are no user serviceable parts in your power tool.
Never use water or chemical cleaners to clean your
power tool. Wipe clean with a dry cloth. Always store
your power tool in a dry place. Keep the motor
ventilation slots clean. Keep all working controls free of
dust.
Occasionally you may see sparks through the
ventilation slots. This is normal and will not damage
your power tool.
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
TECHNICAL SPECIFICATION
Measured values determined according to EN 60745
WARNING: The vibration emission value during actual
use of the power tool can differ from the declared value
depending on the ways in which the tool is used
dependant on the following examples and other
variations on how the tool is used:
How the tool is used and the materials being cut.
The tool being in good condition and well maintained.
The use of the correct accessory for the tool and
ensuring it is sharp and in good condition.
The tightness of the grip on the handles and if any anti
vibration accessories are used.
And the tool is being used as intended by its design
and these instructions.
This tool may cause hand-arm vibration syndrome if its
use is not adequately managed.
WARNING: To be accurate, an estimation of exposure
level in the actual conditions of use should also take
account of all parts of the operating cycle such as the
times when the tool is switched off and when it is
running idle but not actually doing the job. This may
significantly reduce the exposure level over the total
working period.
Helping to minimise your vibration exposure risk.
Maintain this tool in accordance with these instructions
and keep well lubricated (where appropriate)
If the tool is to be used regularly then invest in anti
vibration accessories.
Avoid using tools in temperatures of 10ºC or less
Plan your work schedule to spread any high vibration
tool use across a number of days.
Voltage 230V - 50Hz
Motor 2000W
No load speed 6500min -1
Disc size 230 x 22.2mm
Sound Pressure Level L
pA
92.3 dB(A)
K=3dB(A)
Sound Power Level L
WA
103.3 dB(A)
K=3dB(A)
Vibration Level 10.521m/s 2 , K=1.5m/s 2
Weight 4.6 kg