background image

1

IMPORTANT SAFETY INSTRUCTIONS BELOW

WARNING: 

Failure to provide adequate structural strengthening, prior to installation can result in 

serious personal injury or damage to the equipment. It is the installer’s responsibility to ensure the 

structure to which the component is affixed can support four times the weight of the component and 

any additional apparatus mounted to the component.

WARNING: 

Do not exceed the weight capacity for this product as listed below. This can result in serious 

personal injury or damage to the equipment. It is the installer’s responsibility to ensure that the total 

combined weight of all attached components does not exceed that of the maximum figure stated.

WARNING: 

Risk of death or serious injury may occur when children climb on audio and/or video 

equipment or furniture. A remote control or toys placed on the furnishing may encourage a child to 

climb on the furnishing and as a result the furnishing may tip over on to the child.

WARNING: 

Risk of death or serious injury may occur. Relocating audio and/or video equipment to 

furniture not specifically designed to support audio and/or video equipment may result in death or 

serious injury due to the furnishing collapsing or over turning onto a child or adult.

SAFETY 

DISCLAIMER

ADDITIONAL WARNINGS:

1. 

Keep all documentation/instructions after fitting.

2.  Read all technical instructions fully before installation and use. It is the installer’s responsibility to ensure that all 

documentation is passed on to the end user and read fully before operation.

3. 

Do not use near water or outdoors unless the product has been specifically designed to do so.

4.  Protect any cables or cords being used near this bracket from being walked on or pinched to prevent damage and 

risk of injury. 

5.  Use this product only for its intended purpose as described in the product instructions and only use attachments/

accessories specified by the manufacturer.

6.  Do not operate the product if it is damaged in any way, liquid has been spilled or objects have fallen into the 

apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 

Contact the original installer/manufacturer to arrange repair or return.

WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons:

1.  Clean only with a dry cloth and always unplug any electrical items being used in conjunction with this product before 

cleaning.

Future Sound & Vision trading as Future Automation intend to make this and all documentation as accurate as 
possible. However, Future Automation makes no claim that the information contained herein covers all details, 
conditions or variations, nor does it provide for every possible contingency in connection with the installation or use 
of this product. The information contained in this document is subject to change without prior notice or obligation of 
any kind. Future Automation makes no representation of warranty, expressed or implied, regarding the information 
contained herein. Future Automation assumes no responsibility for accuracy, completeness or sufficiency of the 
information contained in this document.

WARNING – RISK OF INJURY!

Only for use with equipment weighing 

22LBS (10KG) OR LESS

Use with heavier projectors/equipment may lead to instability causing 

tip over or failure resulting in death or serious injury.

Bracket Suitable for Residential and Commercial Use.

Содержание SPS & SA































Отзывы: