Funkwerk artem ComPoint Butterfly Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 118

Funkwerk artem ComPoint Butterfly Скачать руководство пользователя страница 77

The ComPoint in the AC Mode

5-3

•

Security
Specifies whether WEP encryption or WPA-PSK has been activated in
the ComPoint.

•

Current Transmission Rate
Shows the current data transmission rate to the access point. The fol-
lowing values can be displayed: 1, 2, 5,5, 6, 9, 11, 12, 18, 24, 36, 48, 54
Mbps.

•

Current Signal Noise Ratio
The value of the signal noise ratio indicates the difference between
signal and noise. It is an indicator for the quality of the link between
ComPoint and access point.

•

Current Signal Level
Displays the signal level of the signal received by the access point. This
value is specified in dBm. The higher this value, the better the
received signal level.
Values above -82 dBm usually suffice for a transmission rate of 11
Mbps. Below -94 dBm, no communication is possible.

•

Current Noise Level
The noise level specifies the strength of the interfering signals caused
by other sending devices in the 2.4 GHz band, such as Bluetooth
devices, garage door openers, or video transmission systems. If values
above -95 dBm are displayed here, you should try to shift to other
channels.

«
...
75
76
77
78
79
...
»

Содержание artem ComPoint Butterfly























































































































Отзывы:

Нет отзывов