background image

Inflating the Tires 
 
 
 
 
 

 
 

NOTE:

The 6” rear tires are inflated when shipped, but they invariably lose some pressure 

between the point of manufacturing and your purchase. Be sure to inflate the tires to the 
correct PSI before first time use. 

Please read the specification sheet to get the information of tire pressure. 

 

Using a bicycle-style tire pump to inflate the tire to the PSI indicated on the sidewall of the tire. 
 

Note:

 The pressurized air supplies found at gasoline stations are designed to inflate 

high-volume automobile tires. If you decide to use such an air supply to inflate your tires, first 
make sure the pressure gauge is working, then use very 
short bursts to inflate to the correct PSI. If you inadvertently over-inflate the tire, release the 
excess pressure immediately. 
 

Important information of use guider for tire 

Note

: Tire is the only contact surface between the vehicle to the road, the safety of various 

riding activity depends on the small surface of tire where contact with the road. Therefore, it is 

very important to keep the tire in good condition any time and use the correct size and 

standard tire to replace the used ones.

 

Guide: 

Tire assembly and disassembly 

It is strongly recommended that the tire assembly and disassembly should be done by an 

authorized technician with necessary skills. 

Tire inflating pressure 

It is very important to keep the tire in proper pressure and check the tire pressure before use. 

The inflating should be done while the tire is cold. 

Tire maintenance 

Tire tread depth should be checked regularly.( Shallower tread means less grip of tire). You 

must stop to use the vehicle if the tire is pierced, disassemble the tire and check it carefully. 

Tire maintenance should be done by an authorized technician. Tire should be replaced 

immediately when it is distorted or damaged. 

Tire replacement   

It is important to use the correct size and standard tire as per our specification (see details in 

technical specification sheet) 

Don’t use the used tire if you are not sure its previous service condition. 

Tire aging 

Tire aging is unavoidable even the tire is not ever used or just used a few times. Tire aging is 

mainly reflected in the cracked section on side of tire and tire tread, sometimes the tire is 

distorted as well. The used and aged tire should be checked and confirmed if it is ok to use 

again by an authorized technician   

 

 

 

 

Содержание QD03























Отзывы: