Fujitsu SPARC Enterprise T5140 Скачать руководство пользователя

Страница: 24 / 138

SPARC Enterprise T5140 and T5240 Servers Product Notes • November 2012

Notes and Limitations

This section provides notes and describes limitations on this release of the SPARC Enterprise
T5140 and T5240 servers.

■

“Cryptographic Function” on page 14

■

“Hardware RAID Function” on page 14

■

“Cable Management Arm” on page 16

■

“Express Rail Rackmounting Kit” on page 17

■

“SAS RAID Internal HBA Card” on page 17

■

“SSD Storage” on page 17

■

“RFID Tag” on page 20

■

“Changed Behavior When Operating the Solaris OS With Logical Domains” on page 21

■

“Notes on Processor Identification” on page 22

■

“Notes on Using 200V Power Supply” on page 22

■

“Notes on Using Oracle Solaris 11 OS” on page 23

Cryptographic Function

When using the cryptographic function, install the Solaris 10 9/10 or later.

If you use the function in the Solaris OS older than Solaris 10 9/10, apply the patch 142909-
17 or later.

Hardware RAID Function

The SPARC Enterprise T5140 and T5240 servers are equipped with a hardware RAID
function by default, and this section shows the support conditions and the points of concern.

Содержание SPARC Enterprise T5140











































































































































Результаты поиска

Содержание SPARC Enterprise T5140

Отзывы:

Похожие инструкции для SPARC Enterprise T5140

Бренды по названию

Популярные бренды

Fujitsu SPARC Enterprise T5140, Примечания к продукту

Результаты поиска

Содержание SPARC Enterprise T5140

Отзывы:

Похожие инструкции для SPARC Enterprise T5140

Бренды по названию

Популярные бренды