background image

Chapter 2

Important Information About the SPARC Enterprise T5140 and T5240 Servers

21

Changed Behavior When Operating the Solaris OS 
With Logical Domains

This section describes the changes in behavior in using the Solaris OS that occur once a 
configuration has been created by the Logical Domains Manager.

Note – 

OpenBoot firmware is not available after the Solaris OS has started, because it is 

removed from memory. To reach the 

ok

 prompt from the Solaris OS, you must halt the 

domain. You can use the Solaris OS 

halt

 command to halt the domain.

Results from Halting or Rebooting the Control Domain

The following table shows the expected behavior of halting or rebooting the control 
(primary) domain.

TABLE 2-9 

Expected Behavior of Halting or Rebooting the Control (Primary) Domain

Command

Other Domain 
Configured?

Behavior

halt

No

Host powered off and stays off until powered on at the SP.

Yes

Resets and boots up if the variable 

auto-boot?=true

. Resets and halts at 

ok

 prompt if the 

variable 

auto-boot?=false

.

reboot

No

Reboots the host, no power off.

Yes

Reboots the host, no power off.

shutdown

 

–i

 

5

No

Host powered off, stays off until powered on at the SP.

Yes

Resets and reboots.

Содержание SPARC Enterprise T5140











































































































































Отзывы: