Fujitsu PRIMERGY TX1330 M4 Скачать руководство пользователя страница 104

Страница: 104 / 110

104

Operating Manual

TX1330 M4

Technical data

Slots

Drive Bays

Dimensions / weight

Ventilation clearance

There must be a clearance of at least 200 mm in front of and behind the server
to ensure adequate ventilation of the subsystem.

Slot 1: PCIe Gen3 x1
(mechanical x4)

up to 167.65 mm length

Slot 2: PCIe Gen3 x4
(mechanical x4)

notched, up to 167.65 mm length

Slot 3, 4: PCIe Gen3 x8
(mechanical x8)

2x (up to 240 mm length)

Slot notes

In SAS configuration 1x PCI-Express occupied by
modular RAID controller.

HDD bay configuration up to 12x 3.5-inch, for SAS / SATA

or 8x / 16x / 24x 2.5-inch for SAS/SSD optional

Accessible drive bays

3 x 5.25/1.6-inch for backup devices

Notes accessible drives All possible options described in relevant system

configurator.

Tower (W x D x H)

177 x 560 x 455 mm

Rack (W x D x H)

483 x 495 x 174 mm (without projecting parts)

Mounting Depth Rack

543 mm

Weight

Approx. 13 - 28 kg

Weight notes

Weight may vary depending on actual configuration

Rack mounting kit

Rack mounting kit as option

Содержание PRIMERGY TX1330 M4















































































































Результаты поиска

Содержание PRIMERGY TX1330 M4

Отзывы:

Похожие инструкции для PRIMERGY TX1330 M4

Бренды по названию

Популярные бренды

Fujitsu PRIMERGY TX1330 M4, Руководство по эксплуатации

Результаты поиска

Содержание PRIMERGY TX1330 M4

Отзывы:

Похожие инструкции для PRIMERGY TX1330 M4

Бренды по названию

Популярные бренды