Fujitsu PRIMERGY TX1330 M4 Скачать руководство пользователя страница 74

Страница: 74 / 110

Operating Manual

TX1330 M4

Starting up

5.7

Configuring the server with ServerView
Installation Manager

Ensure that the power saving functions are disabled in the

Power

of the BIOS setup during operation.

Advantages of the ServerView Installation Manager

– Wizard-assisted configuration of your server hardware and disk arrays.

– Wizard-assisted installation of all leading server operating systems.

– Wizard-assisted creation of configuration files for unattended installation of

several PRIMERGY servers with identical hardware configurations.

– Installation of drivers and additional software.

The software that can be installed depends on the hardware
configuration of your server. This configuration is detected automatically.

5.7.1

Configuring the server and installing the operating
system

When using the ServerView Installation Manager you can configure the
onboard controller either before or during installation.

Descriptions of operating systems not covered in the RAID controller
manual are provided in the corresponding readme files under:

http://www.fujitsu.com/global/services/computing/server/ia/driver/index.
html

For Japan:

http://www .fujitsu.com/jp/products/computing/servers/primergy/downloa
ds/

Содержание PRIMERGY TX1330 M4















































































































Результаты поиска

Содержание PRIMERGY TX1330 M4

Отзывы:

Похожие инструкции для PRIMERGY TX1330 M4

Бренды по названию

Популярные бренды

Fujitsu PRIMERGY TX1330 M4, Руководство по эксплуатации

Результаты поиска

Содержание PRIMERGY TX1330 M4

Отзывы:

Похожие инструкции для PRIMERGY TX1330 M4

Бренды по названию

Популярные бренды