Fujitsu PRIMERGY TX1330 M2 Скачать руководство пользователя страница 46

Страница: 46 / 86

Operating Manual

TX1330 M2

Hardware installation

5.1

Unpacking the server

CAUTION!

Follow the safety instructions in

"Important information" on page 31

The server must always be lifted or carried by at least two people.
(For the Japanese market, please refer to "

安全上のご注意

".)

Do not unpack the server until it is at its installation location.

Transport the server to the place where you want to set it up.

Unpack all individual parts.

Keep the original packaging in case you want to transport the server again
(applies only to global market).

Check the delivery for any damage during transport.

Check whether the items delivered match the details on the delivery note.

The product name and serial number of the product can be found on the ID card
(see section

"ID card" on page 64

Notify your supplier immediately should you discover that the items
delivered do not correspond to the delivery note.

Содержание PRIMERGY TX1330 M2























































































Результаты поиска

Содержание PRIMERGY TX1330 M2

Отзывы:

Похожие инструкции для PRIMERGY TX1330 M2

Бренды по названию

Популярные бренды

Fujitsu PRIMERGY TX1330 M2, Руководство по эксплуатации

Результаты поиска

Содержание PRIMERGY TX1330 M2

Отзывы:

Похожие инструкции для PRIMERGY TX1330 M2

Бренды по названию

Популярные бренды