Fujitsu MAU3036NC Скачать руководство пользователя | Manualshive

Страница: 59 / 130

background image

C141-E205

4-9

c) In a system which does not use the terminating resistor power supply signal (TERMPWR) on

the SCSI bus, the requirements for +5 VDC given in Figure 4.10 must be satisfied between the
IDD and the SCSI device with the terminating resistor circuit.

Figure 4.10 Power on/off sequence (2)

d) Between the IDD and other SCSI devices on the SCSI bus, the +5 VDC power on/off sequence

is as follows:

•

In a system with its all SCSI devices designed to prevent noise from leaking to the SCSI
bus when power is turned on or off, the power sequence does not matter if the
requirement in b) or c) is satisfied.

•

In a system containing an SCSI device which is not designed to prevent noise from
leaking to the SCSI bus, the requirement given in Figure 4.11 must be satisfied between
that SCSI device and the IDD.

Figure 4.11 Power on/off sequence (3)

SCSI devices
without noise
leaking designed

SCSI devices with
the terminating
resistor

«
...
57
58
59
60
61
...
»

Содержание MAU3036NC



































































































































Отзывы:

Нет отзывов

Похожие инструкции для MAU3036NC

Бренд: R/Evolution Страницы: 58

Бренд: Backyard Discovery Страницы: 43

Mobile Ultra Memory Stick Micro

Бренд: SanDisk Страницы: 1

Бренд: Lifetime Страницы: 32

Tape Library Magstar 3494

Бренд: IBM Страницы: 378

EliteRAID ER104I+

Бренд: Sans Digital Страницы: 64

Бренд: Drobo Страницы: 178

Бренд: AIC Страницы: 105

Бренд: Eastech Flow Controls Страницы: 2

TOWERSTOR TS5CT

Бренд: Sans Digital Страницы: 33

Бренд: Tiger Страницы: 16

Бренд: OpenEye Страницы: 23

Бренд: Rocstor Страницы: 45

AssuredSAN 4544

Бренд: Dot Hill Systems Страницы: 100

EonStor DS B Series

Бренд: Infotrend Страницы: 157

CFexpress CFX-B Series

Бренд: Wise Страницы: 8

Digi Drive Movie

Бренд: Teac Страницы: 9

Бренд: Displays2go Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды