Fujitsu MAU3036NC Скачать руководство пользователя | Manualshive

Страница: 110 / 130

background image

6-14

C141-E205

Table 6.2

System-level field troubleshooting

Item Recommended

work

DC power cable

Check that the power cable is correctly connected to the disk drive and
power supply unit.

Check that the DC voltage is within the specified range (±5%).

Check that +5 VDC supply is 4.75 to 5.25 VDC.

For NC model, check the voltage between pin 36 and 76 of the SCSI
connector.

For NP model, check the voltage between pin 3 and 4 of the power
connector.

DC power level

Check that +12 VDC supply is 11.4 to 12.6 VDC.

For NC model, check the voltage between pin 1 and 2 of the SCSI
connector.

For NP model, check the voltage between pin 1 and 2 of the power
connector.

Make sure the maximum ripple peak-to-peak value of +5 VDC is within
250 mV and +12 VDC is within 250 mV.

Electrical noise

Make sure the high frequency noise (over 20 MHz) is less than 100 mVp-p.

Interface cable connection

Check that the SCSI interface cable is correctly connected between the disk
drive and controller.

Terminating resistors

For a daisy chain connection, check the terminating resistor on the last disk
drive only. For a star-burst connection, check that the terminating resistor
is correctly mounted on all disk drives.

Drive selection address

Check that the disk SCSI ID is set correctly.

Plug setup

Check that the jumpers on the PCA are set so that the disk drive and host
computer operate normally. See Section 5.3.

System cables

Check that all system cables are connected correctly.

System diagnostic test

When possible, execute the system level diagnostic routine as explained in
the host computer manual. This gives a detailed report of a possible fault.

Check the AC voltage from the power supply. Check the DC voltage level
at the power connector for the disk drive.

If the AC voltage level is abnormal or there is a lot of electrical noise,
notify the user of the error.

If the DC voltage level is unstable, replace the power supply unit.

Intermittent or nonfatal errors

If possible, replace the disk drive. If replacing the disk drive does not
eliminate the error, the removed disk drive is probably not faulty. To
continue error analysis, refer to the hardware and software manuals
supplied with the system.

«
...
108
109
110
111
112
...
»

Содержание MAU3036NC



































































































































Отзывы:

Нет отзывов

Похожие инструкции для MAU3036NC

Бренд: Ice-O-Matic Страницы: 9

SO READY SECURE

Бренд: DANE-ELEC Страницы: 2

Бренд: Addonics Technologies Страницы: 2

Бренд: Tennsco Страницы: 4

Бренд: Extreme Tools Страницы: 2

Бренд: Facom Страницы: 2

Бренд: Lowrance Страницы: 32

Бренд: Seagate Страницы: 20

Бренд: Archive Страницы: 131

Бренд: morse Страницы: 7

CFexpress CFX-B Series

Бренд: Wise Страницы: 8

USM32A, USM64A, USM128A, USM256A

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Toshiba Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды