Fujitsu MAU3036NC страница 8 Скачать руководство пользователя | Manualshive

Страница: 8 / 130

background image

vi

C141-E205

Task Alert

message

Page

Damage

1. Be careful of the insertion orientation of the SCSI connectors.

With the system in which terminating resistor power is supplied
via the SCSI cable, if the power is turned on, the overcurrent
protection fuse of the terminating resistor power supplier may
be blown or the cable may be burnt if overcurrent protection is
not provided.

When the recommended parts listed in Table 4.2 are used,
inserting the cables in the wrong direction can be prevented.

2. To connect SCSI devices, be careful of the connection position

of the cable. Check that the SCSI device with the terminating
resistor is the last device connected to the cable.

5-12

Data loss

When the SEND DIAGNOSTIC command terminates with the
CHECK CONDITION status, the INIT must collect the error
information using the REQUEST SENSE command. The RECEIVE
DIAGNOSTIC RESULTS command cannot read out the error
information detected in the self-diagnostics.

6-4

Mounting Installation

Caution

1. To avoid shocks, turn off the power before connecting or

disconnecting a cable, connector, or plug.

2. To avoid injury, do not touch the mechanical assembly during

disk drive operation.

3. Do not use solvents to clean the disk drive.

Caution

1. Always ground yourself with a wrist strap connected to ground

before handling. ESD (Electrostatics Discharge) may cause
the damage to the device.

2. To prevent electrical damage to the disk drive, turn the power

off before connecting or disconnecting a cable, connector, or
plug.

3. Do not remove a PCA. This operation is required to prevent

unexpected or unpredictable operation.

4. Do not use a conductive cleaner to clean a disk drive assembly.

5. Ribbon cables are marked with a colored line. Connect the

ribbon cable to a cable connector with the colored wire
connected to pin 1.

6-5

6-6

Damage

Never open the disk enclosure in the field. Opening the disk
enclosure may cause an irreparable fault.

Data loss

Save data stored on the disk drive before requesting repair. Fujitsu
does not assume responsibility if data is destroyed during servicing
or repair.

6-6

6-7

«
...
6
7
8
9
10
...
»

Содержание MAU3036NC



































































































































Отзывы:

Нет отзывов

Похожие инструкции для MAU3036NC

XCubeNAS XN7012R

Бренд: Qsan Страницы: 16

Azure StorSimple 8100

Бренд: Microsoft Страницы: 12

Cloud Object Storage System Slicestor 2212...

Бренд: IBM Страницы: 50

Бренд: Lifetime Страницы: 20

avigilon NVR4 Series

Бренд: Motorola solutions Страницы: 18

Бренд: Fujitsu Страницы: 12

Бренд: Fujitsu Страницы: 16

Бренд: Fujitsu Страницы: 201

Бренд: Fujitsu Страницы: 14

Бренд: Fujitsu Страницы: 185

Бренд: Fujitsu Страницы: 179

Бренд: Fujitsu Страницы: 176

Бренд: Fujitsu Страницы: 191

Бренд: Fujitsu Страницы: 320

Бренд: Fujitsu Страницы: 191

Бренд: Fujitsu Страницы: 180

Бренд: Fujitsu Страницы: 191

MPF3102AT - Desktop 10.2 GB Hard Drive

Бренд: Fujitsu Страницы: 193

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды