Fujitsu MAU3036NC страница 74 Скачать руководство пользователя | Manualshive

Страница: 74 / 130

background image

5-2

C141-E205

(2) Unpackaging

a) Use a flat work area. Check that the "This Side Up" sign side is up. Handle the package on

soft material such as a rubber mat, not on hard material such as a wooden desk.

b) Be careful not to give excess pressure to the internal unit when removing cushions.

c) Be careful not to give excess pressure to the PCAs and interface connector when removing the

drive from the Fcell.

d) Do not remove the sealing label or cover of the DE and screws.

(3) Installation/removal/replacement

a) Do not attempt to connect or disconnect connections when power is on. The only pin settings

that may be altered are pins 9, 10 (Write Protect) in CN2. (NP model)

b) Do not move the drive when power is turned on or until the drive completely stops (for 30

seconds) after power is turned off.

c) Place and keep removed screws and other parts where they will not get lost or damaged.

d) Keep a record of all maintenance work for replacing.

(4) Packaging

a) Store the drive in an antistatic case (Fcell).

b) It is recommended to use the same cushions and packages as those at delivery. If those at

delivery cannot be used, use a package with shock absorption so that the drive is free from
direct shocks. In this case, fully protect the PCAs and interface connector so that they are not
damaged.

(5) Delivery

a) When delivering the drive, provide packaging and do not turn it over.

b) Minimize the delivery distance after unpacking and avoid shocks and vibrations with cushions.

For the carrying direction at delivery, use one of the mount allowable directions in Subsection
4.2.2 (vertical direction is recommended).

(6) Storage

a) Provide moistureproof packaging for storage.

b) The storage environment must satisfy the requirements specified in Subsection 2.1.3 when the

drive is not operating.

c) To prevent condensation, avoid sudden changes in temperature.

«
...
72
73
74
75
76
...
»

Содержание MAU3036NC



































































































































Отзывы:

Нет отзывов

Похожие инструкции для MAU3036NC

Бренд: Falcon Страницы: 19

Бренд: Palram Страницы: 74

GLADIATOR PLUS 2

Бренд: Asgard Страницы: 6

Бренд: Euromate Страницы: 23

Бренд: SanDisk Страницы: 4

Бренд: TrekStor Страницы: 100

TVS-872N-i3-8G-US

Бренд: QNAP Страницы: 12

NSLU2 - Network Storage Link NAS Server

Бренд: Linksys Страницы: 64

Бренд: IBM Страницы: 122

Бренд: Addonics Technologies Страницы: 2

Бренд: Velleman Страницы: 4

Бренд: QPS Страницы: 9

2big Thunderbolt

Бренд: LaCie Страницы: 72

TVS-h 74t Series

Бренд: QNAP Страницы: 71

Бренд: Drobo Страницы: 178

Бренд: Apricorn Страницы: 36

Бренд: IBM Страницы: 2

URBAN 100.1P DEC

Бренд: garofalo Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды