Two
S t a r t i n g Y o u r L i f e B o o k L S e r i e s
L i f e B o o k L S e r i e s f r o m F u j i t s u
17
C A U T I O N
When you turn on your notebook be
sure you have a power source. This
means that at least one battery is
installed and charged, or that the AC
adapter or the auto/airline adapter is
connected and has power.
When the power switch is turned on, your
notebook carries out a Power On Self Test
(POST) to check the internal parts and config-
uration. If a fault is found a beep will sound
and/or an error message will be displayed.
(See Troubleshooting on pages 156-158.)
Depending on the nature of the problem
you may be able to continue by starting the
operating system or by entering the BIOS
setup utility and revising the settings.
After satisfactory completion of the Power On
Self Test (POST) your notebook will load your
operating system. (See Boot Menu on pages 105-
106 to see which kind of disk will be the source.)
able to use your notebook. (If you wish to
access the BIOS setup utility before you go
through the condition of use process you must
press the
F2
key while the Fujitsu logo is still
visible. If you press the
Esc
key while the
Fujitsu logo is still present you will get a boot
menu dialog box which will allow you to select
which drive is to be used for finding the operat-
ing system.) If you turn off the power without
using the on screen
Cancel
button you will
get an error message when you start your
notebook again.
Condition of Use Process
The first time you start your notebook you
must confirm your acceptance of the copyright
limitations for your pre-installed software. After
you complete the Condition of Use process
these screens will not appear again. There are 6
screens to read carefully and respond to.
You cannot use your notebook until this
Condition of Use process is completed. The
bottom of each screen has a
<Back
button, a
Next>
Button and a
Cancel
button which
are activated by the integrated Touchpad cursor
C A U T I O N
Never turn off your notebook during
Power On Self Test (POST) or it will
cause an error message to be displayed
when you turn your notebook on the
next time. (See the Troubleshooting
information on pages 156-158.)
Booting the System with Windows 98
Other than the AC adapter, we strongly recom-
mend that you do not attach any other external
devices and do not put any CD or floppy disk
in your drives until you have gone through the
initial power on sequence.
When you turn on your notebook for the first
time it will display a Fujitsu logo on the screen.
If you do nothing the system will read the hard
drive for the operating system software, flash
the notebook configuration information on the
screen, and then the Windows 98 Setup Wizard
Screen will appear. You will then be stepped
through the condition of use process. You must
complete this initial process before you will be
Содержание Lifebook L470
