Fujitsu F2MC-16LX Series Скачать руководство пользователя страница 194 | Manualshive

Страница: 194 / 710

background image

176

CHAPTER 4 I/O PORT

4.5.2

Operation of Port 3

The operation of port 3 is explained.

■

Operation of Port 3 (General-purpose I/O Port)

●

Operation of output port

•

When the bit in the port 3 direction register (DDR3) corresponding to the output pin is set to "1", port 3

functions as an output port.

•

When the output buffer is turned "ON" and output data is written to the port 3 data register (PDR3), the

data is retained in the output latch and output from the pin.

•

When the PDR3 is read, the state of the output latch in the PDR3 is read.

●

Operation of input port

•

If the bit in the DDR3 corresponding to the input pin is set to "0", port 3 functions as an input port.

•

The output buffer is turned "OFF" and the pin enters the high impedance state.

•

When data is written to the PDR3, it is retained in the output latch in the PDR3 but not output to the pin.

•

When the PDR3 is read, the level value (Low or High) of the pin is read.

●

Operation of resource input

•

The state of the pin that serves as a resource is input to the resource.

•

When using port 3 as the input pin of the resource, clear the bit in the DDR3 corresponding to the input

pin of the resource to "0" and set the input pin as an input port.

●

Operation at reset

•

When the CPU is reset, the value of the DDR3 is cleared to 0.Consequently, all output buffers are set to

"OFF" (the pin becomes an input port pin), and the pin enters the high-impedance state.

•

The PDR3 is not initialized by reset. Therefore, when using port 3 as an output port, it is necessary to set

output data in the PDR3, and then set the bit in the DDR3 corresponding to the output pin to "1" and to

output.

●

Operation in stop mode, timebase timer mode or watch mode

•

When the pin state specification bit of the low power consumption mode control register (LPMCR:

SPL) is "1", at a transition to the stop mode, timebase timer mode or watch mode, the pin enters the

high- impedance state.The output buffer is set forcibly to "OFF" irrespective of the value of the DDR3

register.

Note:

If read modify write instructions (such as the bit set instruction) are used to read the PDR, the
pin set as an output port by the DDR outputs the desired data. To switch a pin from input port
to output port, write output data to the port data register and use the port direction register to
set the pin as an output port.

«
...
192
193
194
195
196
...
»

Содержание F2MC-16LX Series







































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для F2MC-16LX Series

Бренд: Garmin Страницы: 2

Бренд: Paradyne Страницы: 11

Бренд: Paradyne Страницы: 19

COMSPHERE 3550 Series

Бренд: Paradyne Страницы: 153

Jetstream CPX-1000

Бренд: Paradyne Страницы: 141

4 Channel Input Buffer Board SDAIBB

Бренд: B&B Electronics Страницы: 22

Wireless Connectivity Cape

Бренд: Element14 Страницы: 2

Advanced Flame 1.0

Бренд: Eastern Voltage Research Страницы: 12

Бренд: ADTRAN Страницы: 9

GEFORCE RTX 4090

Бренд: Nvidia Страницы: 160

Бренд: ETAS Страницы: 36

Бренд: VIA Technologies Страницы: 2

Бренд: Roland Страницы: 224

Бренд: Foscam Страницы: 92

ControlWave Remote Ethernet I/O

Бренд: Emerson Страницы: 3

Бренд: Emerson Страницы: 6

Bristol Helicoid Gauges

Бренд: Emerson Страницы: 1

ACC/ARTM-7221/SCSI

Бренд: Emerson Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды