Fujitsu ASYA12LGC Скачать руководство пользователя страница 55

Страница: 55 / 82

08-02

Settings will not be changed if invalid numbers or setting values are selected.

The settings may be selected between the following two: Function Number or Setting Value.

After the power is turned on, perform the "FUNCTION SETTING" according to the installation

conditions using the remote controller.

This procedure changes to the function settings used to control the indoor unit according to

the installation conditions. Incorrect settings can cause the indoor unit malfunction.

Entering the Function Setting Mode

While pressing the FAN button and SET TEMP.( ) simultaneously,

press the RESET button to enter the function setting mode.

STEP 1

Selecting the Remote Control Unit Signal Code

Use the following steps to select the signal code of the remote control unit.

(Note that the air conditioner cannot receive a signal code if the air conditioner

has not been set for the signal code.)

The signal codes that are set through this process are applicable only to the signals

in the FUNCTION SETTING.

For details on how to set the signal codes through the normal process,

refer to SELECTING THE REMOTE CONTROL UNIT SIGNAL CODE.

(1) Press the SET TEMP. ( ) ( ) buttons to change the signal code between .

Match the code on the display to the air conditioner signal code. (initially set to )

(If the signal code does not need to be selected, press the MODE button and proceed to STEP 2.)

(2) Press the TIMER MODE button and check that the indoor unit can receive signals at the displayed signal code.

The air conditioner signal code is set to A prior to shipment.

Contact your retailer to change the signal code.

The remote control unit resets to signal code A when the batteries in

the remote control unit are replaced. If you use a signal code other

than signal code A, reset the signal code after replacing the

batteries.

If you do not know the air conditioner signal code setting, try each

of the signal codes ( ) until you find the code which

operates the air conditioner.

(3) Press the MODE button to accept the signal code, and proceed to STEP 2.

10 c HEAT

8-1-2 Procedures to change the Function Setting for wireless RC

Содержание ASYA12LGC



















































































Результаты поиска

Содержание ASYA12LGC

Отзывы:

Похожие инструкции для ASYA12LGC

Бренды по названию

Популярные бренды

Fujitsu ASYA12LGC, Инструкция по эксплуатации

Результаты поиска

Содержание ASYA12LGC

Отзывы:

Похожие инструкции для ASYA12LGC

Бренды по названию

Популярные бренды