background image

En-11

9. ERROR 

CODES

If you use a wireless remote controller, the lamp on the photo detector unit will output error 
codes by way of blinking patterns. If you use a wired remote controller, error codes will ap-
pear on the remote control display. Refer to the lamp blinking patterns and error codes in 
the table. An error display is displayed only during operation.

Error display

Error code

Description

OPERATION 

lamp 

(green)

TIMER 

lamp 

(orange)

ECONOMY 

lamp 

(green)

(1)

(1)

11

Serial communication error

(1)

(2)

12

• Wired remote controller 

communication error

• Server room control 

communication error

(1)

(5)

15

Check run unfinished 
Automatic airflow adjustment error

(1)

(6)

16

Peripheral unit transmission PCB 
connection error

(1)

(8)

18

External communication error

(2)

(1)

21

Unit number or Refrigerant circuit 
address setting error 
[Simultaneous Multi]

(2)

(2)

22

Indoor unit capacity error

(2)

(3)

23

Combination error

(2)

(4)

24

• Connection unit number 

error (indoor secondary unit) 
[Simultaneous Multi]

• Connection unit number error 

(indoor unit or branch unit) 
[Flexible Multi]

(2)

(6)

26

Indoor unit address setting error

(2)

(7)

27

Primary unit, secondary unit setup 
error [Simultaneous Multi]

(2)

(9)

29

Connection unit number error in 
wired remote controller system

(3)

(1)

31

Power supply interruption error

(3)

(2)

32

Indoor unit PCB model 
information error

(3)

(3)

33

Indoor unit motor electricity 
consumption detection error

(3)

(5)

35

Manual auto switch error

(3)

(9)

39

Indoor unit power supply error for 
fan motor 

(3)

(10)

3A

Indoor unit communication circuit 
(wired remote controller) error

(4)

(1)

41

Room temp. sensor error 

(4)

(2)

42

Indoor unit heat ex. middle temp. 
sensor error

(4)

(4)

44

Human sensor error

(5)

(1)

51

Indoor unit fan motor error

(5)

(3)

53

Drain pump error

(5)

(4)

54

Electric air cleaner reverse VDD 
error

(5)

(5)

55

Filter set error

Error display

Error code

Description

OPERATION 

lamp 

(green)

TIMER 

lamp 

(orange)

ECONOMY 

lamp 

(green)

(5)

(7)

57

Damper error 

(5)

(8)

58

Intake grille error

(5)

(9)

59

Indoor unit fan motor 2 error
(Left side fan)

(5)

(10)

5A

Indoor unit fan motor 3 error
(Right side fan)

(5)

(15)

5U

Indoor unit error

(6)

(1)

61

Outdoor unit reverse/missing 
phase and wiring error

(6)

(2)

62

Outdoor unit main PCB 
model information error or 
communication error

(6)

(3)

63

Inverter error 

(6)

(4)

64

Active filter error, PFC circuit error 

(6)

(5)

65

Trip terminal L error

(6)

(8)

68

Outdoor unit rush current limiting 
resister temp. rise error

(6)

(10)

6A

Display PCB microcomputers 
communication error

(7)

(1)

71

Discharge temp. sensor error

(7)

(2)

72

Compressor temp. sensor error

(7)

(3)

73

Outdoor unit Heat Ex. liquid temp. 
sensor error

(7)

(4)

74

Outdoor temp. sensor error

(7)

(5)

75

Suction Gas temp. sensor error

(7)

(6)

76

• 2-way valve temp. sensor error
• 3-way valve temp. sensor error

(7)

(7)

77

Heat sink temp. sensor error

(8)

(2)

82

• Sub-cool Heat Ex. gas inlet 

temp. sensor error

• Sub-cool Heat Ex. gas outlet 

temp. sensor error

(8)

(3)

83

Liquid pipe temp. sensor error

(8)

(4)

84

Current sensor error

(8)

(6)

86

• Discharge pressure sensor error
• Suction pressure sensor error
• High pressure switch error

(9)

(4)

94

Trip detection

(9)

(5)

95

Compressor rotor position 
detection error (permanent stop) 

(9)

(7)

97

Outdoor unit fan motor 1 error

(9)

(8)

98

Outdoor unit fan motor 2 error

(9)

(9)

99

4-way valve error

(9)

(10)

9A

Coil (expansion valve) error

(10)

(1)

A1

Discharge temp. error

(10)

(3)

A3

Compressor temp. error

(10)

(4)

A4

High pressure error

9387603095_IM.indb   11

9387603095_IM.indb   11

2019/11/18   15:54:55

2019/11/18   15:54:55

Содержание ASUG09LZAS













Отзывы: