Fujitsu AOU36RLXFZH Скачать руководство пользователя страница 8

Страница: 8 / 20

En-7

(5) During heating operation, drain water

ows from the outdoor unit.

Therefore, install the outdoor unit in a place where the drain water

ow will not be

obstructed. (Reverse cycle model only)

(6) Do not install the unit where strong wind blows or where it is very dusty.
(7) Do not install the unit where people pass.
(8) Install the outdoor unit in a place where it will be free from being dirty or getting wet by

rain as much as possible.

(9) Install the unit where connection to the indoor unit is easy.

4. 2. 1. Single outdoor unit installation
When the upper space is open:

[Unit: in. (mm)]

(1) When there are obstacles at the

rear only.

5-7/8 (150)

or more

(2) When there are obstacles at the

rear and sides.

7-7/8 (200)

or more

9-13/16 (250)

or more

11-13/16 (300)

or more

(3) When there are obstacles at the

front only.

39-3/8 (1000)

or more

(4) When there are obstacles at the

front and rear.

39-3/8 (1000) or more

5-7/8 (150) or more

When there is an obstruction in the upper space:

[Unit: in. (mm)]

(1) When there are obstacles at the

rear and above.

Max. 19-11/16 (500)

11-13/16 (300)

or more

39-3/8 (1000)

or more

(2) When there are obstacles at the rear, sides,

and above.

39-3/8 (1000)

or more

19-11/16 (500)
or more

7-7/8 (200)

or more

9-13/16 (250)

or more

Max. 19-11/16
(500)

4. 2. 2. Multiple outdoor unit installation

• Provide at least 25 mm of space between the outdoor units if multiple units are

installed.

• When routing the piping from the side of an outdoor unit, provide space for the piping.
• No more than 3 units must be installed side by side.

When 3 units or more are arranged in a line, provide the space as shown in the
following example when there is an obstruction in the upper space:

When the upper space is open:

[Unit: in. (mm)]

(1) When there are obstacles at the

rear only.

11-13/16 (300)

or more

9-13/16 (250)

or more

(2) When there are obstacles at the front

only.

9-13/16 (250)

or more

59-1/16 (1500)

or more

(3) When there are obstacles at the front and rear.

19-11/16 (500) or more

59-1/16 (1500) or more

9-13/16 (250)

or more

When there is an obstruction in the upper space:

[Unit: in. (mm)]

• When there are obstacles at the rear and above.

59-1/16 (1500)

or more

19-11/16 (500)

or more

Max. 11-13/16

(300)

59-1/16 (1500)

or more

9-13/16 (250)

or more

4. 2. 3. Outdoor units installation in multi row

[Unit: in. (mm)]

* The following settings are not recommended in case of cooling in a low outside

temperature.

(1) Single parallel unit arrangement

19-11/16 (500) or more

23-5/8 (600) or more

59-1/16 (1500) or more

118-1/8 (3000) or more

(2) Multiple parallel unit arrangement

19-11/16 (500) or more

23-5/8 (600) or more

59-1/16 (1500) or more

137-13/16 (3500) or more

9-13/16 (250) or more

9-13/16 (250)

or more

59-1/16 (1500)

or more

19-11/16 (500)
or more

4. 3. Placing the unit

WARNING

Do not touch the

ns. Otherwise, personal injury could result.

CAUTION

When carrying the unit, hold the handles on the right and left sides and be careful. If
the outdoor unit is carried from the bottom, hands or

ngers may be pinched.

• Be sure to hold the handles on the sides of the unit. Otherwise, holding the suction

grille on the sides of the unit may cause deformation.

Handle

9380545101-02_IM.indb 7

2/26/2016 10:16:04 AM

Содержание AOU36RLXFZH





















Результаты поиска

Содержание AOU36RLXFZH

Отзывы:

Бренды по названию

Популярные бренды

Fujitsu AOU36RLXFZH, Руководство по установке

Результаты поиска

Содержание AOU36RLXFZH

Отзывы:

Бренды по названию

Популярные бренды