Fujitsu Siemens Computers CELSIUS M430 Скачать руководство пользователя

Страница: 40 / 90

Troubleshooting and tips

Time and/or date is not correct

You can set the time and date in the

BIOS Setup

or in the operating system.

►

Set the time and date.

If the time and date are repeatedly wrong when you switch on your PC, the on-board
battery is flat. Change the lithium battery as described in the "System expansions"-
"Replacing lithium battery".

Error messages on the screen

Error messages and their explanation are contained:

●

in the manual for the mainboard

●

in the "BIOS Setup" manual

●

in the documentation for the programmes used

Restoring the hard disk contents

Should you need to restore your hard disk, the instructions are provided on the case of the
"Recovery CD" (delivered with your system).

Tips

The workstation cannot be switched off with the ON/OFF switch

Cause: The workstation has not been switched on with the ON/OFF switch.

►

Press the ON/OFF switch again.

Cause: System crash

►

Press and hold the power button for at least four seconds until the workstation switches off.

Out of system resources

If you have too many applications running at once, you may experience problems due to a lack of
system resources. In this case you should:

►

close unnecessary applications

►

run the applications in a different order

Other manuals

Additional manuals are provided as PDF files on the "User Documentation" or "Drivers & Utilities"
CD.

A26361-K665-Z126-1-19, edition 1

Содержание CELSIUS M430



























































































Результаты поиска

Содержание CELSIUS M430

Отзывы:

Похожие инструкции для CELSIUS M430

Бренды по названию

Популярные бренды

Fujitsu Siemens Computers CELSIUS M430, Руководство по эксплуатации

Результаты поиска

Содержание CELSIUS M430

Отзывы:

Похожие инструкции для CELSIUS M430

Бренды по названию

Популярные бренды