Fujitsu Siemens Computers AB* G45LRTA Скачать руководство пользователя страница 24

Страница: 24 / 81

1-19. OFF DEFROST OPEARTION CONTROL

01-21

1. OFF DEFROST OPERATION CONDITION

When operation stops in the [Heating operation] mode, if frost is adhered to the outdoor unit heat

exchanger, the defrost operation will proceed automatically. In this time, if indoor unit operation

lamp flashes slowly (7 sec ON / 2 sec OFF), the outdoor unit will allow the heat exchanger to defrost,

and then stop.

In heating operation, the outdoor heat exchanger temperature is less than -4°C,

and compressor operation integrating time lasts for more than 30 minutes,

and compressor operation contiguous time lasts for more than 10 minutes.

OFF Defrost Flow Chart

Heating operation stop

Outdoor heat exchanger temperature :

Below -4°C

and

Compressor integrating operation :

Over 30 minutes

and

Compressor contiguous operation:

Over 10 minutes

Defrost start

Defrost Indicater:

[Operation lamp]

7 sec ON / 2 sec OFF

Outdoor heat exchanger temperature : Over 10°C

Compressor ON time : Maximum 15 minutes

Defrost end

2. OFF DEFROST RELEASE CONDITION

Release Condition

Outdoor heat exchanger temperature is higher than 10°C

Compressor operation time has passed 15 minutes.

( Table 14 : OFF Defrost Release Condition )

OFF defrost operation is released when the conditions becomes as shown in Table 14.

Содержание AB* G45LRTA


















































































Результаты поиска

Содержание AB* G45LRTA

Отзывы:

Похожие инструкции для AB* G45LRTA

Бренды по названию

Популярные бренды

Fujitsu Siemens Computers AB* G45LRTA, Инструкция по эксплуатации

Результаты поиска

Содержание AB* G45LRTA

Отзывы:

Похожие инструкции для AB* G45LRTA

Бренды по названию

Популярные бренды