manualshive.com logo in svg

Fujitec MO-1330, Инструкция по эксплуатации

Поделиться
Скачать
Fujitec MO-1330 Скачать руководство пользователя страница 7

4．Operation

※Be sure to perform inspection and test run before operation start.

■Inspection before operation start check if that:

① Driving shaft of screwdriver unit is free from any trouble.

② Controller is free from any trouble.(Fusing,etc)

③ Each cable is free from any trouble.(Damage,crack,etc)

④ Each cable is connected correctly.

Please drive start of work when you can confirm the check above.

■Trial operation
After inspection,perform trial operation to check the unit for trouble.
If any trouble should be found, be sure to repair as soon as possible.

■Operation

① Set screwdriver select switch in the front of controller in accordance with model No. of

electric screwdriver used.
※MO-1330→133，MO-1350→135（DO-1390A、DO-1390A-2）
【Caution】If screwdriver's model No. does not coincide with the selected No. on the swich,
screwdriver may not work or motor may be burned.

② Set torque knob on controller to desired fastening torque value.

(For torque value, refer to torque chart on page 7.)

③ Turn ON power switch on controller. Then, make sure that power indicator lights.

■Stop

Turn OFF power switch on controller and make sure that power indicator goes off.

－6－

Содержание MO-1330


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды