manualshive.com logo in svg

Fujitec MO-1330, Инструкция по эксплуатации

Поделиться
Скачать
Fujitec MO-1330 Скачать руководство пользователя страница 5

3

Controller（DO-1390A-2） For  MO-1330・1350

①Screwdriver select switch

Set to screwdriver model No.

②Torque volume 1

Use to change torque.

③Torque volume ２

Use to change torque.

④Power switch（POWER）

Use to turn ON / OFF power of control unit.

⑤Power indicator

Light while power of control unit is ON.

⑥Overcurrent indicator lamp（OCP）

⑦Torpue change switch connector（3P）

Torque 1 and  torque 2 can be switched.

⑧Metal outlet（2P）

Connected to input/output signals.
Panel side ： PLT-162-R  Harness side  ： PLT-162-P

⑨Fuse holder（3A）

Used to protect and replace fuse.

⑩Metal outlet（5P）

Connected to input/output signals.
Panel side ： PLT-165-R  Harness side  ： PLT-165-P

⑪Power cord

Plugged into AC100V power source.

⑫Adjustment at motor lock time

Can it tighten and the following maintenance officer be adjusted.

⑫

Adjustment at motor lock 

⑨

Fuse holder 

⑧

 Metal outlet(2p) 

⑦

Torque switch 

⑩

Metal outlet 

⑪

Power cord 

①

Screwdriver select switch 

②

Torque volume1 

⑥

Overcurrent 

indicator lamp 

③

Torque volume2 

④

Power switch 

⑤

Power 

indicator 

－4－

Содержание MO-1330


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды