
www.fubag.ru
O
m
perator's
anual
-
-
8
The installation and connection of MIG Welding
1. Connection and installation of the wire feeder
2. Connection between Welder and Torch
3. Connection of the Connection Cable
The installation and connection of
Welding
Connection of welder and welding cable
Connection of welder and grounding cable
- Select suitable wire according to welding
technology. The wire diameter must be
matched with drive roll, wire guide pipe liner
and contact tip.
Open the lid of wire reel on the wire feeder put
“Wire Coil” into “Wire Reel” on the wire feeder.
Wire end under the “Wire Reel”,
opposite wire feeder.
There is damping screw device in the “Wire
Reel” (hex head screw will be seen when open
the lid). Pull the wire reel with hand when
adjust. If resistance is over large, may adjust
damping bolt: screw clockwise will enlarge the
value and vice versa.
- Lead wire into “Wire Guide Pipe” of wire
feeder, align wire with roll groove through
“Drive Roll”, re-lead “Socket Tip” and press
“Drive Roll”. (If more welding wire is needed, it
will be done after switching on the power.)
- Insert the connector of torch into “Torch Access Hole” on the front panel of the welder and rotate
the screw cap firmly.
Connect the copper tip of the earth clamp which thread through the wire access hole on the panel
with “-“ of the “connecting tip”. The connecting cable must be reliable, or the connecting tip will burn
out.
In order to reach sound performance when welding with flux-cord wire, it’s available that connect
the “+”, “-” in an opposite way, that’s the wire feed motor with “-“and the connecting cable with “+”.
Do not use steel plate or the materials alike which are ill conductor to connect between
welder and work piece.
Connect the quick connector of welding cable to the output on front panel, and deasil turn down.
The electrode holder is used for clamp the electrode
Connect the quick connector of grounding cable to the output on the front panel, and deasil turn
down. The earth clamp is used for clamp the work piece
Do not use steel plate or the materials alike which are ill conductor to connect between
welder and work piece.
-
-
-
-
.
.
Attention:
Notice:
Notice:
MMA
1.
2.
FRONT
PANEL
TORCH
WIRE
EARTH CABLE
FEED ROLLER
Содержание INMIG 200 Plus
