
www.fubag.ru
O
m
perator's
anual
-
-
10
www.fubag.ru
O
m
perator's
anual
Attention:
-
‘
’
‘
’
.
-
.
-
.
-
.
-
.
-
.
.
а)
-
.
elect protect gas by button
, and the indicators at the left part of button will indicate the selection
gas
The protection indicator light will be on after a long time operation, it shows that the inner
temperature is over the permitted data, then the machine should be stopped using for some time to
let it cool down. It can continue using after the protection indicator light is off
The power source should be switched off after the operation or while temporarily leaving job site
Welders should dress canvas work cloth and wear welding mask to prevent the hurt from arc and
thermal radiation
Light separating screen should be put in the job site to prevent the arc will hurt other people
Inflammable or explosive materials are prohibited to access the job site
Each connection of the welder should be connected correctly and creditably
Wire, groove and surrounding 10-20 mm site must be cleaned, no existing rust, greasy dirt, water
and paint etc
Debugging before welding
Install the torch, gas and welding wire, and then turn on the power switch. The power indicator is on
and fan works
- S
20
.
Work Piece cleaning Before Welding
MIG welding steps
-
.
-
-
Turn on the gas regulator of gas tank,
the gas pressure is shown on the meter
.
-
knob 14
.
-
knob 14
.
Turn the gas control counterclockwise.
Press the welding voltage
the
display shows «GAS ON»
With gear, adjust the gas supply in
accordance with the specifications. To
stop the flow of gas press the welding
voltage
again, the display
shows «GAS OFF»
If the welding procedure requires work
mode spot welding (SPOT), you must
configure during this operation. To do
this, press and hold the welding voltage
up until appears «SPt ADJ»
Rotate the welding voltage, the desired
setting time duration welding one point.
knob 14
А
V
А
V
А
V
А
V
Содержание INMIG 200 Plus
