FSR MAS-7000 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 52

background image

22

MAS-7000

The following options are available for this menu item:

Mode

Function

Normal

The two interlaced

fi

elds are simply combined together. This will

often show artifacts on moving images, but can be used when the

input is known to be still.

Auto

Automatically selects Film 3:2 or Medium Range Motion

Compensation (M. Comp Med.) depending on whether Film

Mode is detected or not. For 1080i sources, a special de-

interlacing mode is selected to eliminate combing effects.

Film 3:2

Enables 3:2 pull down conversion of the incoming NTSC video.

(This option is ignored if the source is not NTSC video).

M.Comp Low

M.Comp Med.

M. Comp High

Enables Pixel Adaptive Motion Compensation. Three levels are

available with ‘Low’ providing the least compensation for Motion

and ‘High’ providing the most compensation.

Frame/bob

The two

fi

elds are shown consecutively

Input: RGB1

Input: RGB1

Diagonal Interp [ON] [OFF]

Diagonal Interp [ON] [OFF]

This menu item allows the user to specify whether the source has diagonal interpolation applied to it when de-
interlacing occurs. This reduces ‘jagged’ artifacts on moving images, however is not suitable for noisy sources
where the noise could be mis-interpreted as a diagonal or sloping element of the picture..

Input: RGB1

Input: RGB1

Noise Reduction [ON] [OFF]

Noise Reduction [ON] [OFF]

This menu item allows the user to specify whether the source has noise reduction applied to it. This is performed
by averaging the video signal over a number of

fi

elds – but ignoring areas where motion has occurred. If motion

blurring is seen, it is recommended to turn this setting off.

Input: RGB1

Input: RGB1

F. swap [Off] Offset [-4-+3]

F. swap [Off] Offset [-4-+3]

This menu item is only available when “Advanced menus” in the System Settings Group is turned on. It can
correct for an interlaced source with abnormal odd/even

fi

eld characteristics. With F. swap “ON”, the odd and

«
...
20
21
22
23
24
...
»

Содержание MAS-7000





















































Отзывы:

Нет отзывов

Похожие инструкции для MAS-7000

Бренд: Hama Страницы: 9

Бренд: Hama Страницы: 10

Бренд: Hama Страницы: 12

Бренд: T+A Страницы: 54

Бренд: TA Страницы: 32

Бренд: B&B Electronics Страницы: 7

Бренд: C&C TECHNIC Страницы: 2

Бренд: Lika Страницы: 2

Бренд: ILX Lightwave Страницы: 16

Бренд: Casti Страницы: 4

Бренд: Missing Link Страницы: 8

Vizionlink PCIE-VL-3120

Бренд: TechNexion Страницы: 2

Бренд: Conceptronic Страницы: 7

Deye SUN-8K-SG01LP1-EU

Бренд: V-TAC Страницы: 50

Бренд: SIIG Страницы: 12

Бренд: Sungrow Страницы: 11

Бренд: IVIEW Страницы: 40

Бренд: Mitsubishi Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды