FSR MAS-7000, Инструкция по установке и эксплуатации

Страница: 11 / 52

11
MAS-7000
MAS-7000 MENU TREE
FSR MAS-7000
www.fsrinc.com
FSR Version #
Menu Select
Output Adjust
Menu Select
Input Adjust
Menu Select
Scaler Adjust
Menu Select
System Settings
Output Resolution
[1-117]
HDCP
[On] [Off]
Output Type
[RGB1] [YUV1]
[DVI-D1] [VID1]
[VID2] [SV1] [SV2]
Exit
Zoom Level
[100 - 1000] in 10
step increments
H / V Zoom Pan %
[H] [V]
Image Freeze
[On] [Off]
H / V Out Shift
[H] [V]
Shrink Level
[10% - 100%]
[On] [Off]
H / V Position
[H] [V]
Aspect Adjust
[Simple] [Advance]
[Pixel]
Image Smoothing
[Off] [Med]
[High] [Auto]
Image Flip
[Off] [H] [V]
[H & V]
FSR Version #
Software Date
In
[XX.XXX] Hz
[XX.XXX] TL
Select To Save
Current
LCD Backlight
[On] [Off]
Auto Threshold
[Low] [Medium]
[High] [Very High]
RS232 Baud Rate
[9,600] [19,200]
[28,800] [33,600]
[38,400] [57,600]
Buzzer
[On] [Off]
Resolutions
Power Cycles
Firmware Updates
Hours In Use
Auto Setup
[Inactive]
[Phase Adjust]
Top / Left Adjust
[-120 - +120]
[-120 - +120]
BTM / Right Adjust
[-120 - +120]
[-120 - +120]
Audio Input #
[1 - 4] [Mute]
Phase Adjust
[0 - 30]
RGB Input Type
[Auto] [D-RGB]
[D-YUV] [A-RGB]
[A-YUV]
RGB / VYU Level
[50 - 200]
[50 - 200]
[50 - 200]
Sharpness
[-3 - +4]
Luma Delay
[-4 - +3]
Back to root
menu
Input [RGB1]
[YUV1] [DVI-D1]
[VID1] [VID2]
[SV1] [SV2]
Diagonal Interp.
[On] [Off]
Input To Adjust
[RGB1] [YUV]
[SV1] [VID1]
[SV2] [VID2]
Color [0 - 180]
Hue [-90 - +90]
Brightness [0 - 180]
Contrast [0 - 180]
Adjust Resolution
WARNING -
Adjust With Care
Image To Adjust
[1 - 122]
Only active when
"Advanced" menu is "on"
under system settings.
Interlaced
[On] [Off]
Horrizontal
Frequency Coarse
[XX.XXX] KHz
Horrizontal
Frequency Fine
[XX.XXX] KHz
Lines / F
[XXX] = XX.XXX Hz
H / V Active
[XXX] x [XXX]
H / V Start
[0 - 1023]
[0 - 1023]
H / V Sync
[8 - 1023]
[1 - 1023]
Sync Polarity
[+H +V] [-H +V]
[+H - V] [-H -V]
Aspect Change
[Normal]
[Letterbox]
[Pillarbox]
On Source Loss
[Show] [Freeze]
[Blue] [Black]
[Remove]
On Source Loss
[Show] [Freeze]
[Blue] [Black]
[Remove]
Adjust Preset
[1] [Load] [Store]
[Erase]
System Settings
Advanced Menu
[On] [Off]
H / V CROP
[H] [V]
Temporal Interp.
[On] [Off]
[DVI-D1]
Aspect Correct
[Fill] [Aspect]
[H-Fit] [V-Fit] [1:1]
YUV Black Level
[0] [7.5] IRE
F.Swap [On] [Off]
Offset - [-4 - +3]
Noise Reduction
[On] [Off]
HDCP
(Active / Inactive)
[On] [Off]
Display Emul
[Mem1-6]
[DVI] [Mon]
EDID Capture
[Mem1-6]
[Grab]
Auto Setup
[Inactive]
[Phase Adjust]
Aspect Correct
[Fill] [Aspect]
[H-Fit] [V-Fit] [1:1]
Top / Left Adjust
[-120 - +120]
[-120 - +120]
BTM / Right Adjust
[-120 - +120]
[-120 - +120]
On Source Loss
[Show] [Freeze]
[Blue] [Black]
[Remove]
Audio Input #
[1 - 4] [Mute]
Phase Adjust
[0 - 31]
RGB Input Type
[Auto] [D-RGB]
[D-YUV] [A-RGB]
[A-YUV]
RGB/VYU Level
[50 - 200] [50 - 200]
[50 - 200]
YUV Black Level
[0] [7.5] IRE
De-Int.
[Normal / Weave]
[Auto] [Film 3:2]
[M. Comp. Low]
[M. Comp. Med.]
[M. Comp. High]
[Frame / Bob]
Diagonal Interp.
[On] [Off]
Noise Reduction
[On] [Off]
F.Swap [On] [Off]
Offset - [-4 - +3]
Aspect Correct
[Fill] [Aspect]
[H-Fit] [V-Fit] [1:1]
BTM / Right Adjust
[-120 - +120]
[-120 - +120]
Top / Left Adjust
[-120 - +120]
[-120 - +120]
Audio Input #
[1 - 4] [Mute]
Input (Format)
[PAL BGDHI / NTSC M]
[NTSC 4.43 50 / PAL 60]
[PAL N / NTSC 4.43 60]
[NTSCN 3.58 / PAL M]
[NTSC - Japan 3.58]
[SECAM]
[B & W 50hz / 60hz]
De-Int.
[Normal / Weave]
[Auto] [Film 3:2]
[M. Comp. Low]
[M. Comp. Med.]
[M. Comp. High]
[Frame / Bob]
De-Int.
[Normal / Weave]
[Auto] [Film 3:2]
[M. Comp. Low]
[M. Comp. Med.]
[M. Comp. High]
[Frame / Bob]
Diagonal Interp.
[On] [Off]
Noise Reduction
[On] [Off]
F.Swap [On] [Off]
Offset - [-4 - +3]
CLKS / L
[XXX]=XX.XXXMHz