manualshive.com logo in svg

FSR EXPLORER XP Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
FSR EXPLORER XP Series Скачать руководство пользователя страница 15

  Explorer XP Matrix   

 

 

 

 

 

 

 

 

 

15

                       

MATRIX LCD READOUT MENU TREE

Output Audio Level:

The output audio level control has the range of  +5 to -45 dB. When the minimum volume is reached 
the output will be muted, thus providing the best possible isolation. 

To adjust the output level use the up/down buttons untill the desired output is on the LCD is 
indicated. Press Select, then use the up or down buttons to adjust the setting.  

When the desired level 

is reached press ESC to select the next output.

Press ESC to save your current setting to non-volatile memory and return to the main menu mode.

Audio Input Trim:

The input audio trim controls have a range of  +15 to -5 dB. 
To adjust use the up and down arrows in main menu mode till the LCD reads AUDIO INPUT 
LEVEL, then press Select. You are now in input select state.

Use up/down buttons till the desired input is displayed on the LCD. Press Select, then use the up or 
down buttons to go to the desired setting

.  When the desired level is reached press ESC to select the 

next output.

Содержание EXPLORER XP Series













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды