Frymaster FPGL30 Скачать руководство пользователя страница 21

Страница: 21 / 56

2-9

Check the programmed temperature thermostat setting. (Refer to chapter 4 3000

Computer

Instructions

) for the setpoint programming instructions for your particular controller.)

2.5 Converting to another Gas Type

DANGER

This appliance was configured at the factory for a specific type of gas. Converting from

one type of gas to another requires the installation of specific gas-conversion compo-

nents. Conversion instructions are included with conversion kits.

Switching to a different type of gas without installing the proper conversion

components may result in fire or explosion. NEVER ATTACH THIS APPLIANCE TO A

GAS SUPPLY FOR WHICH IT IS NOT CONFIGURED!

Conversion of this appliance from one type of gas to another should only be performed

by qualified, licensed, and authorized installation or service personnel, as defined in

Section 1.7 of this manual.

OCF30

™

Series gas fryers manufactured for non-CE countries use different burners for each type gas.

The burners in fryers built for Propane gas have a special gray-colored coating on the burner tiles to

enable them to withstand the higher caloric value of the Propane gas. Burners designed for use in

propane units may be used in natural gas applications, but not vice versa.

Non-CE Gas Conversion Kits

Natural Gas to Propane (LP) Gas

Propane (LP) Gas to Natural Gas

Full Vat before 10/2010: PN 826-2527

Full Vat before 10/10: PN 826-2528

Dual Vat before 10/2010: PN 826-2529

Dual Vat before 10/10: PN 826-2530

Full Vat after 09/2010: PN 826-3278

Full Vat after 09/10: PN 826-2967

Dual Vat after 09/2010: PN 826-3279

Dual Vat after 09/10: PN 826-2968

Non-CE Gas Conversion Kits for Australia

Natural Gas to Propane (LP) Gas

Propane (LP) Gas to Natural Gas

Full Vat before 10/2010: PN 826-2745

Full Vat before 10/10: PN 826-2747

Dual Vat before 10/2010: PN 826-2746

Dual Vat before 10/10: PN 826-2748

Full Vat after 09/2010: PN 826-2969

Full Vat after 09/10: PN 826-2971

Dual Vat after 09/2010: PN 826-2970

Dual Vat after 09/10: PN 826-2972

Units manufactured for export to CE countries are equipped with “universal” burners that may be used

with either Natural (G20, G25) gas or Butane (G30) and Propane (G31) gasses.

CE Gas Conversion Kits for Units with Gas Valve 810-1715

G20 or G25 (Natural) to G30 or G31 Gas:

G30 or G31 to G20 or G25 (Natural) Gas:

before 10/2010 PN 826-2973

before 10/10 PN 826-2974

after 09/2010 PN 826-3278

after 09/10 PN 826-2976

Содержание FPGL30

























































Результаты поиска

Содержание FPGL30

Отзывы:

Похожие инструкции для FPGL30

Бренды по названию

Популярные бренды

Frymaster FPGL30, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание FPGL30

Отзывы:

Похожие инструкции для FPGL30

Бренды по названию

Популярные бренды