manualshive.com logo in svg

Frymaster FGP55 Series, Руководство по обслуживанию и запасным частям

Поделиться
Скачать
Frymaster FGP55 Series Скачать руководство пользователя страница 42

 

FGP55 SERIES RETHERMALIZERS 

CHAPTER 2:  PARTS LIST 

 

 

2-5 

2.2 Components and Controllers  

 

ITEM PART 

# 

COMPONENT 

1 

826-2117 

Spark Module (Domestic and CE) 

* 

106-3553SP 

Cable, Ignition with Rajah Connector 

2 

210-3638 

Panel, Control- Computer FGP55 

3 

106-3938 

Computer, Assembly FGP55 includes item 4 

4 

823-3820 

Bezel Assembly, Control Panel 

5 

106-2338 

Harness, Computer Wire Assembly 

6 

106-1768SP 

ECO Connector (Honeywell Valves Only- 

CE ONLY

) 

* 

810-2398 

ECO Connector (Robertshaw Valves Only- 

CE ONLY

) 

7 

106-2361SP 

Probe Assembly (RTD), Temperature, Dean Computer 

* 

106-0987 

Harness, Wire-Temp Probe 

* 809-0888 

Clip, 

Tinnerman 

* 

810-2164 

Spring, Space- Electronic Thermostat Probe 

* 

810-2046 

Spring, Spacer- High Limit Capillary Bulb 

8 

210-4367 

Clamp, Electronic Thermostat Probe 

9 

106-2351SP 

Harness, Wiring Spark Module 

10 

106-2353 

Harness, Relay Component Wire 

11 

106-2352 

Harness, Transformer/Fuse Wire 

12 

106-2349 

Harness, Low Level Float wire 

13 

106-2344 

Harness, High Level Float Wire 

14 803-0278 

 

L-Brush 

* Not illustrated 

Содержание FGP55 Series



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды