background image

 

FGP55 SERIES RETHERMALIZERS 

CHAPTER 2:  PARTS LIST 

 

 

2-2 

2.1  FGP55 Primary Components (cont.) 

 

ITEM PART 

COMPONENT 

823-3817SP 

Cookpot- W/A- FGP55 

2 810-2034 

Manifold, 

Gas 

810-2048 

Orifice, Natural Gas (G20/25) #39 (2.53 mm) 

 

810-2060 

Orifice, Natural Gas (G20/25) #42 (2.40 mm) 

 

810-2059 

Orifice, LP Gas (G30/31) #53 (1.51 mm)  

 

810-2297 

Orifice, MFG Gas #13 (4.70 mm) 

106-1839SP 

Pilot Burner Assembly- Natural (G20/25) Gas 

 

106-1128SP 

Pilot Burner Assembly- LP (G30/31) Gas 

810-0705 

Tube, Pilot Gas Supply- ¼ x 23" 

810-0703 

Tube, Pilot Gas Supply- ¼ x 17½ " 

106-3553SP 

Cable, Ignition with Rajah Connector 

807-1310 

Flame Sensor  

200-3618 

Bracket, Manifold Support Right 10.88" 

 

200-3619 

Bracket, Manifold Support Left 12.35" 

6 210-8387 

Diffuser 

 

200-3614 

Burner Mounting Bracket 

810-2151 

Burner, Left Side - Cast Iron 

810-2149 

Burner, Center - Cast Iron 

 

810-2785 

Burner, Universal - Stamped Steel 

10 

810-2150 

Burner, Right Side – Cast Iron 

11 823-3248 

Leg 

Support 

Assembly 

12 

807-3552 

Gas Valve, Natural Gas, Electronic Ignition 24 VAC 

 

807-3628 

Gas Valve, LP Gas, Electronic Ignition 24 VAC 

 

810-2156 

Gas Valve, Natural Gas 120 VAC 

 

810-2323 

Gas Valve, LP Gas 120 VAC 

 

807-2091 

Gas Valve, G20/G25 Gas 24 VAC 

(CE ONLY)

 

 

807-2127 

Gas Valve, G31 Gas 24 VAC 

(CE ONLY)

 

13 

210-3631 

Channel, Front and Rear FGP155 

 

220-0320 

Channel, Front and Rear FGP255 

14 

200-1675 

Lower Hinge Bracket 

15 

211-3632 

Side Panel, Left Side 

16 

212-3632 

Side Panel, Right Side 

200-3663 

Magnet, Plate Door 

17 

106-2358 

Wireway, Control Panel Assembly 

(see Sec. 2.4 for components)

 

18 

210-3627 

Bracket Hinge, Left 

19 

210-3640 

Bracket Hinge, Right 

20 

824-1093 

Top Cap- FGP155-after Aug. ’02 

(use 824-1054 prior to 08/02)

 

 

824-1620 

Top Cap- FGP255 

* 230-1232 

Joiner 

Strip 

FGP255 

21 106-2355 

Flue 

Assembly 

22 210-3630 

Flue 

Cap 

(use 210-3625 for Flue Deflector)

 

23 106-2346SP 

Door 

Assembly 

810-1422 

Handle, Door – after April ’02 

(use 810-2105 prior to 04/02)

 

* 200-1301 

Pin, 

Door 

810-0066 

Magnetic Catch, Door 

* Not illustrated 

Содержание FGP55 Series



















































Отзывы: