Fronius TransSteel 2700c Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 120

background image

-----

An invalid welding process was called up on the robot interface (no. 37) or
an empty flag was selected (no. 32)
Call up a valid welding process or select assigned "Save" button

Cause:

Remedy:

ELn | 8

The connected wire-feed unit is not supported
Connect supported wire-feed unit

Cause:
Remedy:

ELn | 12

Different control panels for selecting materials are in the system
Connect similar control panels to select materials

Cause:
Remedy:

ELn | 13

Invalid change of welding process during welding
During welding do not carry out any illegal change of the welding process,
reset error message by pressing any button

Cause:
Remedy:

ELn | 14

More than only one robot interface is connected
Only one robot interface may be connected, check the system configuration

Cause:
Remedy:

ELn | 15

More than only one remote control unit is connected
Only one remote control unit may be connected, check the system configur-
ation

Cause:
Remedy:

Err | IP

The power source control has detected a primary overvoltage
Check the mains voltage.
If the service code is still present, turn off the power source, wait 10
seconds, and then turn on the power source.
If the fault persists, contact After-Sales Service

Cause:
Remedy:

Err | PE

The earth current watchdog has triggered the safety cut-out of the power
source.
Switch off the power source
Place the power source on an insulating surface
Connect the grounding (earthing) cable to a section of the workpiece that is
closer to the arc
Wait for 10 seconds and then switch the power source on again

If you have tried this several times and the error keeps recurring, contact
After-Sales Service

Cause:

Remedy:

Err | Ur

If the VRD option is available, the open circuit voltage limit of 35 V has been
exceeded.
Switch off power source
Wait for 10 seconds and then switch the power source on again

Cause:

Remedy:

99

EN

«
...
97
98
99
100
101
...
»

Содержание TransSteel 2700c

























































































































Отзывы:

Нет отзывов

Похожие инструкции для TransSteel 2700c

Storm Responder 5500

Бренд: Briggs & Stratton Страницы: 48

Бренд: RAFFEL SYSTEMS Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 9

EverPlay BT7900

Бренд: Philips Страницы: 14

Бренд: Philips Страницы: 16

Бренд: Onan Страницы: 28

Бренд: Electro Adda Страницы: 31

Бренд: Accu Страницы: 16

Бренд: VIETA Страницы: 32

Бренд: Connect Systems Страницы: 54

Бренд: Rothenberger Страницы: 20

Бренд: Wacker Neuson Страницы: 130

Бренд: Mackie Страницы: 11

Бренд: Daewoo Страницы: 45

Бренд: JB Systems Страницы: 8

Бренд: Campbell Hausfeld Страницы: 48

Бренд: Uniden Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды