4
Rev.0 16/11/2021
Operator Panel | ROBOT - POST
4
DISPLAY (V)
1
2
3
Picture 2 - DISPLAY (V)
Loading of parameters:
takes place automatically by selecting the
desired programme.
Saving of parameters:
if the LED of the
RESET
key
(E)
is turned off,
press the
RESET
key for more than 4 seconds. This LED will start to
flash rapidly to indicate that the parameters have been saved.
The program P=00 is read-only and it is configured with default values.
Up to 99 programmes can be created (based on the machine
model):
To copy the parameters of an existing program on a virgin
program, select the program source, press and hold
RESET
and act
on
P+
and
P-
buttons to select the target program. Release the
RESET
button within 4 seconds the parameters will be copied only, if held
down for more than 4 seconds and then released, will be copied and
saved.
NB
: The virgin target programme must always be released (
F00
=1) (LED
of the
RESET
key
(E)
is turned off).
Automatic opening of the program used previously.
When the machine is turned on again, the parameters from the last
programme selected and started will be loaded.
Keyboard block/ release:
prevents modification of parameters by
blocking the keys
V+
e
V-
; hold down at the same time
F+
and
F-
and
then press
RESET
to enable / disable the block. When the active function
the right LED of the display
(V)
lights up and stays lit.
The disabled/enabled status remains even after the machine has been
turned off and on again.
In some models, a password is required for unlocking:
'P=”PA” F=”SS” V=PASSWORD
to enter; acting on
V+
and
V-
it is
possible to modify the value, press the RESET
(E)
key to confirm the
entered password.
FIGURE
1) indicates the decimal point (values from 0.00 to 9.99)
2) indicates the decimal point (values from 0.0 to 9.9)
3)
indicates the block status of keyboard
ON: keyboard blocked (
V+
and
V-
blocked)
OFF: keyboard released (
V+
e
V-
sbloccati)
Signals
The LED of the
RESET
key
(E)
indicates the writing protection status of
the selected programme. If turned on, it is not possible to rewrite the
modified parameters. It is necessary to select the parameter
F00
on
the same programme to carry out modifications and set the value 1
in the parameter, and then hold down
RESET
for at least 3 seconds. If
the programme is to be saved and at the same time blocked in writing,
after saving it, set 1 in parameter
F00
(padlock open) and then 0 again
(padlock closed) and then hold down
RESET
for at least 3 seconds.
The LED will blink fast only pressing the
RESET
for more than 3 seconds,
indicating the machine is ready to store the parameters; by depressing
the
RESET
button, the parameters will be stored.
The LED will blink slow only to report the alarm status.
The LED next to the MANUAL BATTERY push-button indicates that the
machine is running and flashes to indicate reserve.
The LED next to the MANUAL CARRIAGE RISE indicates the automatic
command of the carriage rise.
The LED next to the MANUAL CARRIAGE DESCENT indicates the
automatic command of the carriage descent.
Battery charge
Press the pushbutton
(H)
when the machine is on and stopped, the
display
(V)
will shows the battery charge level: maximum charge = 100;
minimum charge = 0.
The LED next to the button STOP PAUSE flashes when the battery
reaches a charge of 30%.
Indication of the weight of film consumed (Opt)
At the end of each cycle (or by selecting the parameter
CF
on the display
(F)
), the machine will indicate the consumption of the film in grams
on the display
(V)
and showing
CF
on the display
(F)
. To obtain good
precision, correctly set the thickness of the film in the parameter
F24.
NOTE:
It is also possible to order models with film consumption
expressed in metres. In this case as well, to obtain good precision,
correctly set the diameter of the measurement roller in the parameter
F24
.
Содержание FR330
Страница 2: ...2 Rev 0 16 11 2021 Operator Panel ROBOT POST 2...
Страница 4: ......
Страница 25: ......
Страница 26: ...Hinterbergstrasse 26 6312 Steinhausen Switzerland Fromm Holding AG...
