Fritsch premium PULVERISETTE 14 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 48

Fritsch premium PULVERISETTE 14 Скачать руководство пользователя страница 21

4.5 Ambient conditions

WARNING!
Mains voltage
– The device may only be operated indoors.
– The surrounding air must not contain any electrically

conductive particles.

– Maximum relative humidity 80% for temperatures up

to 31 °C, linearly decreasing down to 50% relative

humidity at 40 °C.

n

The room temperature should be between 5 and 40 °C.

n

Altitudes up to 2000 m

n

Degree of pollution 2 according to IEC 60664-1:2007.

4.6 Electrical connection

DANGER!
Provide short-circuit protection!
Risk of damage due to short-circuits.
– Make sure that the socket is connected to a mains line

protected with a residual current circuit breaker.

DANGER!
Mains voltage!
Changes to the connection line may only be made by a

qualified person.

CAUTION!
Ignoring the values on the type plate may result in damage

to the electrical and mechanical components.

Installation

- 21 -

«
...
19
20
21
22
23
...
»

Содержание premium PULVERISETTE 14

















































Отзывы:

Нет отзывов