Fritsch premium PULVERISETTE 14 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 48

Fritsch premium PULVERISETTE 14 Скачать руководство пользователя страница 14

n

Unauthorised alteration of the PULVERISETTE 14 premium line will

void Fritsch's declaration of conformity to European directives and

void the guarantee.

n

Only use the PULVERISETTE 14 premium line when it is in proper

working order, as intended and in a safety- and hazard-conscious

manner adhering to the operating manual. In particular, immediately

rectify any malfunctions that could pose a safety hazard.

n

If, after reading the operating manual, there are still questions or

problems, please do not hesitate to contact our specialised per-

sonnel.

2.6 Protective equipment

Protective equipment is to be used as intended and may not

be disabled or removed.
All protective equipment is to be regularly checked for

integrity and proper functioning.

For start-up, the housing cover (9) must be closed.
The housing cover is locked:

n

without mains connection

n

during operation

The mill does not start up if:

n

no labyrinth disk has been inserted

n

no collecting vessel has been inserted

n

the collecting vessel is not covered with a lid.

The temperature at the labyrinth disk is monitored in the grinding

chamber. If the disc is heated above 80 °C, the PULVERISETTE 14 pre‐

mium line switches off automatically.

The hood can only be opened when the mill's drive is at

standstill.

Safety information and use

- 14 -

«
...
12
13
14
15
16
...
»

Содержание premium PULVERISETTE 14

















































Отзывы:

Нет отзывов