Fristam Pumps FKL 15 Скачать руководство пользователя страница 9

Страница: 9 / 40

3.5

Accessories

The FKL Pump Series can be equipped with the following acces-
sories, among others:

– Enclosure

Stainless steel enclosure for the gear motor. The enclosure is
fastened to the base frame.

– Spherical cap bearings

Spherical cap bearings for pump setup. Spherical cap bear-
ings are attached to the base frame of the pump.

Other accessories are available. If you have any questions, please
contact

Fristam

3.6

Type Designation

Fig. 8

Type designation example

Note: If the (optional) pump without motor is supplied, please
first read

Chapter 12, "Appendix 2 – Assembly Instructions (Optio-

nal)," page 34

Transportation

Transportation may only be performed by trained personnel.

The pump unit can be moved using an industrial truck or a
crane.

4.1

Safety Instructions

Falling or Unsecured Parts

Severe crush injuries.

►

Always wear gloves when performing transportation-related
work.

Incorrect Positioning of Pump for Transportation

Leakage of caustic, toxic, or contaminating liquids. Personal in-
jury and material damage from contamination.

►

Always move the pump in the installation condition.

Open, Unsealed Pipe Fittings

Material damage from contamination, impact, or moisture in the
pump.

►

Remove the pipe fitting covers just prior to connection to
the pipes.

4.2

Moving With Industrial Truck

WARNING

Unsecured Parts

Serious injuries, pinching of extremities, material damage.

►

Before moving the pump secure it to prevent it from tipping
over. Secure the pump to the pallet with tie-down straps, or
screw the pump to the pallet.

Preparation

►

Ensure that the pump is adequately secured to the pallet, for
example, with straps; see

Fig. 9, "Moving with industrial truck,"

page 9

►

Consider the pump weight when selecting the means of
conveyance. Information on pump weight can be found on
the pump's rating plate as well as in the

Order-Related Docu-

ments

in the attached documents.

Procedure

1. Pick up the pallet with the forks on the industrial truck.

2. Move the pallet to the designated location slowly and

smoothly and set down.

Fig. 9

Moving with industrial truck

Pump type

Supplementary character 1

Pump size

Supplementary character 2

(17) Pump Type

FKL

Circumferential piston pump, self-priming

(18) Supplementary Character 1

Vertical connections

(19) Pump Size

Pump size number

(20) Supplementary Character 2

Pump casing with heating jacket

Pump cover with heating jacket

Rectangular inlet

Содержание FKL 15









































Результаты поиска

Содержание FKL 15

Отзывы:

Fristam Pumps FKL 15, Оригинальное руководство пользователя, Страница: 9 / 40

Результаты поиска

Содержание FKL 15

Отзывы: