Fristam Pumps FKL 15 Скачать руководство пользователя страница 24

Страница: 24 / 40

/ / FKL PUMP SERIES / / /

CAUTION

►

Align the stationary seal ring to the cylindrical pins of the
mechanical seal chamber.

8. Secure the parts with the snap ring

(93-1.60)

Final assembly of pump casing:

9. Secure the assembled mechanical seal chamber

(914.60)

with the screws to the pump casing

(101)

For tightening torques, see table below:

Table 13 Tightening torques for fixture of mechanical seal chamber

10. Mount the pump casing on the shafts and slide it onto the

gearbox.

11. Screw the sealing water tube

(701.60)

into the GLRD casing

and seal it.

CAUTION

The pump casing is not flush with the gearbox. Material
damage from warpage of pump casing.

►

Secure the pump casing with the hex head screws in the
pump casing to the gearbox:

Table 14 Tightening torques for fixture of pump casing

12. To complete the assembly of the shaft seal, mount the ro-

tors, see

Chapter 10.9.2, "Mounting of the Rotors," page 24

10.9.2 Mounting of the Rotors

Fig. 36

Installation of rotors

1. Insert the O-rings

(50)

in the grooves on the rotors.

Note: Only for pump size 15-20: Insert the keys for the rotors
into the shafts.

CAUTION

Mixing up of the two rotors (48). Material damage during
pump operation from rotor blockage or scraping.

The rotors have been adapted to the synchronizing shaft or
the drive shaft and are marked by prick punch marks (inden-
tations):

One indentation for drive shaft

Two indentations for synchronizing shaft

►

Before installing the rotors check the markings.

►

Mount the rotors on the appropriate shafts.

2. Attach the rotor fasteners

(49)

and the belonging seals. Pay

attention to the eccentric fastener: The washer must be flush
with the face of the shaft.

Note: The washer is omitted in FKL 600.

WARNING

Rotating machine parts. Severe pinching of hands.

►

Block the rotors with wooden or plastic wedges.

3. Tighten the rotor fasteners to the specified tightening

torque. See the following table for the tightening torques:

10.9.3 Pump Sealing

Fig. 37

Pump sealing

Pump Size

Casing screws
Tightening Torque [Nm]

600

Pump Size

Casing screws
Tightening Torque [Nm]

600

149

Pump Size

Rotor Fastener
Tightening Torque [Nm]

15 to 75

150

250 to 580

600

108

Table 15 Tightening torques for rotor fasteners

Содержание FKL 15









































Результаты поиска

Содержание FKL 15

Отзывы:

Fristam Pumps FKL 15, Оригинальное руководство пользователя, Страница: 24 / 40

Результаты поиска

Содержание FKL 15

Отзывы: